查询词典 elastic modulus

This paper introduces the method in measuring the elastic modulus E of Epon photoelas-tic materials by means of the electrical measurement at normal temperatures and comparesthe method with the levev extensometer.

本文介绍常温下用电测法测环氧树脂光弹性材料弹性模量E的方法，并与杠杆引伸仪法做了比较。

The first part of our experiment is the elastic modulus measurement of human fresh fibular shaft and 317L stainless steel, and in second part, finite element models of fibula under different operational status were set up, stress distribution was cal...

实验分两部分进行，首先测定人新鲜腓骨和 31 7L医用不锈钢的弹性模量，然后运用有限元程序软件分别建立各术式下腓骨的有限元模型，进行应力计算，并经统计学方法处理。

The modal tests of PCB and PCB assembly (free boundary condition and fixed boundary condition) were carried out. The equivalent elastic modulus and damping parameters of PCB can be gained, and the fixed boundary condition of finite element model was also determined. These will help to the following work.Second, drop impact tests of three different heights were carried out. Strains and acceleration responses of PCB were measured. Failed BGA packages of different test conditions were dyeing, and cross section analysis of failed solder joints was conducted.

针对JEDEC标准试件的局限性，提出了设计便于统计学研究焊点可靠性的试验试件的构想，利用有限元模态分析方法确定并验证了用圆形PCB组件替代JEDEC标准试件的可行性；通过一系列模态试验和有限元模态分析，确定了圆形PCB组件的相关试验参数，这不仅为跌落碰撞下PCB组件有限元模拟确定了较为合理准确的有限元模型，而且为正确地评价跌落碰撞下PCB组件的可靠性问题奠定了基础。2。

The modal tests of PCB and PCB assembly (free boundary condition and fixed boundary condition) were carried out. The equivalent elastic modulus and damping parameters of PCB can be gained, and the fixed boundary condition of finite element model was also determined. These will help to the following work. Second, drop impact tests of three different heights were carried out. Strains and acceleration responses of PCB were measured. Failed BGA packages of different test conditions were dyeing, and cross section analysis of failed solder joints was conducted. It was found in our drop tests that the root cause of lead-free solder joints under drop impact was the combined effect of mechanical shock and PCB bending vibration.

针对JEDEC标准试件的局限性，提出了设计便于统计学研究焊点可靠性的试验试件的构想，利用有限元模态分析方法确定并验证了用圆形PCB组件替代JEDEC标准试件的可行性；通过一系列模态试验和有限元模态分析，确定了圆形PCB组件的相关试验参数，这不仅为跌落碰撞下PCB组件有限元模拟确定了较为合理准确的有限元模型，而且为正确地评价跌落碰撞下PCB组件的可靠性问题奠定了基础。

A series of porous metallic matrix with various porosity and good shapes were manufactured through adjusting the partitioning among Ni-Cr filler, high temperature solid grains and foamer by loose powder sintering. The elastic modulus of the matrix was measured.

以松装烧结方法为基础，通过调整Ni-Cr合金钎料、高温固相颗粒和造孔剂的配比，采用合适的烧结工艺，制备出具有不同孔隙率、形貌较好的多孔金属胎体试样，并测量了胎体试样的弹性模量。

Results. PVA-C compressive elastic modulus increased with increasing PVA concentration and number of FTC's.

结果：PVA-C压缩弹性模量随着PVA浓度和FTC数的升高而增加。

The main content consists of three parts:(1) analyzing the structural dynamic changing rule considering SSI effect;(2) analyzing the earthquake response of traditional non-shake -isolate frameworks before or after considering SSI effect, and then summarizing the rules that how factors such as base-soil elastic modulus and damping ratio effect structural horizontal deflection, displacement between floors and girder-end moment;(3) analyzing the earthquake response of shake-isolate frameworks considering SSI effect or not, indicating the changes after considering SSI effect and the performance of rubber shake-isolate pad.

本文采用通用有限元程序ANSYS，对在7度多遇地震时El Centro波作用下框架的地震响应进行了分析，主要内容分为三部分：（1）分析了考虑SSI效应后结构的动力特性变化规律；（2）对传统非隔震框架结构考虑SSI效应前后的地震响应进行了分析，总结出地基土弹性模量、体系阻尼比等因素对结构各层水平位移、层间位移以及梁端弯矩的影响规律；（3）对考虑与不考虑SSI效应的基础隔震结构的地震响应进行了分析，指出了考虑SSI效应后基础隔震结构地震响应的变化规律和隔震效果。

The results indicate that its dynamic stress-strain curve is hyperbolic type. The dynamic strain of LCES decreases with increasing confining pressure, cement content, curing ages and cyclic loading frequency when it is subjected to the same dynamic stress. At the same dynamic strain, the dynamic secant elastic modulus E_(sec of LCES increases and the damping ratio decreases with increasing confining pressure, cement content, curing ages and cyclic loading frequency. The curves ofσ_d～ε_d,E_～ε_d and D～ε_d with different EPS content intersect respectively, the trend of LCES deformation characteristic is inversely proportional to EPS content near the intersection. The value of dynamic strain at the intersection is about 0.5%~3.0%, the magnitude of which is related to the mixing proportions and confining pressure.

试验结果表明，LCES的动应力应变骨干曲线形态符合双曲线；在相同的动应力作用下，LCES产生的动应变随着固结压力、水泥掺量、试样养护龄期和振动频率的增大而减小；在动应变相同的情况下，随着固结压力、水泥掺量、试样养护龄期和振动频率的增大，LCES的动模量增大而阻尼比减小；随着加载次数的增大，LCES的动模量在开始阶段显著降低，然后趋于稳定，但当加载次数达到几百次时，动模量又有增大的趋势；不同EPS掺入比的LCES的动应力应变骨干曲线、动模量随应变变化曲线和阻尼比随应变变化曲线都发生了相交，交点前后EPS掺入比的大小对LCES动力变形特性的影响趋势是截然相反的，交点处的动应变值一般在0.5％～3.0％范围内变化，其大小与LCES的配比以及固结压力有关。

The nano-hardness and elastic modulus of the ceramic coating were determined using Nano Indenter XP system.

用纳米显微力学探针测定了陶瓷层的纳米硬度和弹性模量。

1 This test method is based on the penetration of a specific type of indentor when forced into the material under specified conditions. The indentation hardness is inversely related to the penetration and is dependent on the elastic modulus and viscoelastic behavior of the material. The geometry of the

4.1本测试方法是根据有关规定，将指定类型的压足压入测试材料进行测量的，反言之，硬度与压入量有关，同时又与材料的弹性模量和粘弹性能有关。

Singer Leona Lewis and former Led Zeppelin guitarist Jimmy Page emerged as the bus transformed into a grass-covered carnival float, and the pair combined for a rendition of "Whole Lotta Love".

歌手leona刘易斯和前率领的飞艇的吉他手吉米页出现巴士转化为基层所涵盖的嘉年华花车，和一双合并为一移交&整个lotta爱&。

This is Kate, and that's Erin.

这是凯特，那个是爱朗。