查询词典 elastic buffer

It is found that in certain water ratio and consolidation pressure, the values of initial elastic modulus and principal deviator stress increase with intermediate principal stress increasing; in certain intermediate principal stress, the values of initial elastic modulus and principal deviator stress increase with water ratio falling.

试验结果表明：在一定的含水率和固结压力下，偏差应力和初始切线模量均随中主应力比b的增大而增大；在中主应力比b确定的情况下，偏差应力和强度最大值随着含水率的增大而减小。

The centerline of elastic rod or elastic filament can be abstracted as space curves to deal with them by the knowledge of the theory of space curve and differential geometry.

由于弹性杆的中心线或弹性细丝可以抽象成空间曲线，然后根据空间曲线论和微分几何的知识进行处理。

The deflection curve differential equation of beam body structure on elastic foundation is solved, relationship of variables between its internal force and coefficient of elastic foundation is formulated.

通过求解弹性基础上梁体结构挠度曲线微分方程，建立了梁体结构内力与基础系数间的关系，分析了混凝土徐变等特性对梁体应力的影响。

The in-plane equivalent elastic modulus and tensile strength of stitched composite laminates are studied, and its found that the in-plane equivalent elastic modulus decreases with the increase of stitch density, stitch thread diameter, maximal misalignment angle and the distortion width, and the range is about 5%. The tensile strength of stitched composite laminate increases with the increase of stitch step and decreases with the stitch space.

研究结果表明：随着缝纫密度、缝纫线直径、最大纤维偏转角和缝纫变形区宽度的增加，缝纫复合材料层合板面内等效模量逐渐降低，最大降幅一般在5%左右；缝纫复合材料层合板的拉伸强度随缝纫针距的增加而增大，随缝纫行距的增加而降低，因此缝纫密度对拉伸强度的影响程度要看具体的缝纫针距和行距。

ABSTRACT Photoplasticity is a method using the high polymer model with the transparent double refraction phenomenon and defining the object's elastic-plastic strain field by the optical image stripe which went beyond the elastic limit.

光塑性法是应用具有透明双折射现象的高分子材料的模型，由超过材料弹性极限下模型的光学图象条纹来确定物体弹塑性应变场的一种方法，这种方法又称为非线性光力学法。

In this paper, a detail analysis of the circumferential through-crack in the cylindrical shells with different boundary restraints is performed by means of the elastic-plastic finite element method. The results obtained provide the application of some analysis methods of elastic-plastic fracture parameters such as Dugdale model with a necessary theoretical base.

本文针对柱壳周向壁穿裂纹，利用弹塑性有限元的数值解，在不同的约束条件下进行了较为详细的分析，获得了一些带有规律性的结果，为Dugdale模型等一些弹塑性断裂参数计算方法的应用提供了必要的理论基础。

At last, the paper has discussed the aggregate technique of discrete method, and analyzed the compute method of cross elastic coefficient and direct elastic coefficient in discrete model, then studied the method used in practice.

最后，本文对非集计模型的集计方法，以及非集计模型交叉弹性系数和直接弹性系数的计算方法进行分析，为非集计模型在实践的应用进行了一些探索。

Based on the calculated elastic constant, the elastic moduli of characteristic plane (101) are figured, which offers reference to mechanical study of these materials afterward.

根据计算的弹性常数绘制了这些材料特征平面(101)面的弹性模量图，为这方面材料的力学研究提供参考。

High-elastic and constant elastic alloys, low expansion and fixed-expansion alloy.

高弹和恒弹性合金，低膨胀和定膨胀合金等。

In the base of calibrating the elastic constant of cantilever and analysis adhesion force, the force information from force curve was obtained and the elastic modulus of single voxel was calculated.

考虑了成型点剩余部分形变对结果分析的影响，在标定微探针弹性系数和对粘附力进行分析的基础上，提取了力曲线中所包含的力学信息，推算出了成型点的弹性模量，得到了成型点的弹性模量低于宏观材料弹性模量的结论。

You can do some assertiveness training.

你可以进行一些自信训练。

We were well on the path to making a rear-wheel-drive global platform," says Mays."

我们正致力于建立一个后轮驱动的平台，"Mays这样说道。"