查询词典 ejector pin
- 与 ejector pin 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
In the top drawing the ejector pin is in the rear position, and it is held back by push-back pins.
在上面的图里,顶杆是在后面的位置,由回程杆带回。
-
The plain diameter ejector pin may be used in one of two ways.
普通的顶杆可以有两种使用方法。
-
The direction of movement of this ejector pin is, therefore, controlled by this hole.
因此顶杆的运动方向由这个孔来控制。
-
In the design of the cavity mould, the diameter of the ejector pin is usually determined based on one's experience or according to analogism.
在型腔模设计中,推杆直径大小的确定一般是根据经验或依据类比法确定,这样确定的推杆往往与生产实际有一定的差距,通过对推杆的受力状况进行分析,从理论计算角度对推杆直径进行确定。
-
Both plain and countersunk headed types of ejector pin are available as standard parts in an extremely large number of sizes ranging from 1.5 mm to 32 mm diameter respectively.
普通的和沉头的顶杆是标准件,标准的尺寸范围很广,直径分别从1.5mm 到32mm 。
-
This hitter method has the advantage that should tile ejector pin break only the small-diameter portion has to be remade.
这后一种方法有一个优点,就是如果顶杆折断,只要重做小直径的部分即可。
-
Yasheng is focus on manufacturing tools and precise specializing parts in IC packaging and test industry and other Micro-electric industry, which is specializing manufacturing various tools (stack magazine, container, wafer cassette, work table, Inspection jig etc.), high accuracy parts (ejector pin, efo-torch, capillary screw, clamp finger, test finger etc), and instrument in Semiconductor industry.
上海雅盛致力于集成电路封装业以及其他微电子工业,专业生产半导体行业生产中使用的各种工具(不锈钢料盒、不锈钢周转箱、晶片盒、不锈钢工作台、检测夹具等);高精密零部件(顶针、打火杆、螺丝、压脚、钩针、测试片等)及仪器。
-
The diagram illustrates a stepped ejector pin manufactured from a solid rod.
图示的阶梯型顶杆用一根实心杆做成。
-
Mold-base check: checking the interference of additional structures (spring, ejector pin, etc.).
模具基地检查:检查附加物干扰。
-
Since some components such as ejector pin, locating ring, sprue bush, water junctions and springs are not included in the mould base, these components are purchased independently.
由于某些原件诸如顶针、定位环、浇口套、弹簧等是不包含在模架里的,因此需要单独购买。
- 推荐网络例句
-
It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.
从鲍尔点的形成原理出发,分析对称连杆曲线上鲍尔点的产生条件,提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。
-
The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.
集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品,年生产总值3000万美元,产品价廉物美、选料上乘、质量保证,深受国内外客户的青睐
-
The eˉtiology of hemospermia is complicate,but almost of hemospermia are benign.
血精的原因很,以良性病变为主。