查询词典 edges and corners

It is hard for women to resist the temptation of jewelries and women's jewelry box is like an abysm which is never full. Therefore, the brand jewels with unique design are good for them while the large ones with edges and corners should be avoide...

标签是一种更为灵活的文章分类方式，您可以为每篇日志添加一个或多个标签，添加标签后的文章会自动出现在和讯博客的相关栏目中。

Inside and outside the hand exchange, will install the circlip and the edges and corners return to original state then.

、将内外把手互换，安上卡簧和棱角还原即可。

First, according to the model chart ruler, opens cutting the gate hole two, the decision opens the door the direction, changes the slanting tongue direction three, inside and outside the adjustment the hand direction (if: The symmetry holds the hand, does not need to exchange holds about the hand adjustment then), holds the hand like left and right AND gate to open the direction asymmetrically to be opposite, invites you: A, takes down the circlip and the edges and corners with the special-purpose circlip pliers.

一、按样板图尺，开凿门孔二、决定开门方向，改为斜舌方向三、调整内外把手方向（若：对称执手，无需调换执手调整左右即可），非对称执手如左、右与门开启方向相反，请您： A、用专用卡簧钳取下卡簧和棱角。

He always is working messy, outside sending, sell or waiter, the face with trenchant edges and corners, billows not the eye of Jing, just see I just show alarmed expression, next the dishcloth dish in the hand is rare in ground falls down.

他总是打着零乱的工，送外卖或者跑堂，棱角分明的脸，波澜不惊的眼睛，只是看见我才露出惊慌的表情，然后手里的抹布盘子稀里哗啦地掉下来。

Then we must be very, very long time, then we will do that only after many, many sad, long enough to give birth exuviate sharp edges and corners of the shell, long to have a single blow of its own, become infinitely strong courageous.

那么我们一定要经过很长很长是时间，那么我们一定要经过很多很多的悲伤，漫长到足够蜕生出棱角鲜明的外壳，漫长到曾经不堪一击的自己，变得无限勇敢坚强。

This machine is suitable to grinding process for different sizes and thickness of the hemline, edges and corners of flat glass.

本机适用于不同尺寸和厚度的平板玻璃的直线底边及棱角的磨削加工。

Her latish works look more grave and frosty with hard curves and convex levels which reflect on edges and corners of modern cities as well as on how "love", a gentle and soft word, becomes metallike coldness after being structurized.

稍后的创作更强调边线，有着&硬边&的冷峻和&凸起&的层次，对应着的则是&当代都市中的棱角&，以及对于&爱这个温柔而热烈的字眼，逐渐被结构化之后的'冰冷'属性&的深刻反省。

All 1#~5# grinding wheels are equipped on the same active girder, and can be used to kibbling, exactly grinding, polishing the hemline of glass from 0°to 45°; 6#~9# grinding wheels are used to exactly grinding and polishing the edges and corners of the hemline.

机器1#~5#磨轮安装在同一活动梁上，可以从0°~45°对玻璃直线底边进行粗、精磨及抛光加工；6#~9#磨轮分别是直线底边棱角的精磨及抛光。

When you fold the analysis of a mark line well-distributed, so that the entire line of flat, and mark; and scrape marks point to edges and corners are distinct, but the book these special molding semi-products, every 5 this cross-laminated broadcasting applanation machine applanation until the fully finished post-drying.

折挝痕线时用力要均匀，使整条痕线平直地翻起，并刮平痕角，使其棱角分明，把对裱成型的半成品书，每5本交叉叠放送压平机压平，待充分干燥后。

Crack reasons for this are: the heating temperature is too high as a result of quenching or cooling in a hurry, the quality of thermal stress and metal volume changes in the organization of the anti-stress than the breaking strength of steel; the work of the original surface defects (such as surface micro-cracks or scratches) or the internal defect of steel (such as slag, serious non-metallic inclusions, white point, the residual cavity, etc.) formed in the quenching stress concentration; serious Decarburization and carbide surface segregation; parts after quenching Back lack of timely or tempering fire; processes in front of the stress caused by excessive cold red, forging folding, turning deep marks, sharp edges and corners, such as the oil groove.

造成这种裂纹的原因有：由于淬火加热温度过高或冷却太急，热应力和金属质量体积变化时的组织应力大于钢材的抗断裂强度；工作表面的原有缺陷或是钢材内部缺陷（如夹渣、严重的非金属夹杂物、白点、缩孔残余等）在淬火时形成应力集中；严重的表面脱碳和碳化物偏析；零件淬火后回火不足或未及时回火；前面工序造成的冷冲应力过大、锻造折叠、深的车削刀痕、油沟尖锐棱角等。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。