查询词典 dynamic test

The static model of torsion joint is based on that of bending joint. The effects of structure parameters inside air pressure, initial angle, rube average radius, rube shell thickness on the turning angle are analyzed and the following conclusions are drawn: the relationship between the angle of torsion joint and the inside air pressure is basically linear, the angle of torsion joint increases with the initial angle and rube average radius, the angle of torsion joint decreases while the rube shell thickness increases. The kinetic equation is built for torsion joint. Simulating experiment implies that the time of inflating and deflating process is extremely shorter than that of kinetic process. So the pneumatic process can be ignored in actual system design and control. The factors that affect the dynamic features of torsion joint, such as shell thickness of rubber tube, average radius, initial angle, connector's outlet area, moment of inertia and viscous damping coefficient, are analyzed and the following conclusions are drawn: the change of rube shell thickness has no effects on the dynamic process of FPA inside air pressure while greatly affects the turning angle of torsion joint; when the rube shell thickness is small, the torsion joint has a bigger turning angle, no overshoot and long risetime, when the shell thickness is big, the turning angle of torsion joint is small, but has high response speed, overshoot and low shock; when the rube average radius increases, the turning angle of torsion joint increases and the overshoot increases too; when the initial angle of torsion joint is big, the turning joint is big, the overshoot is small and shock is low, but the risetime is big; the connector's outlet area affects the dynamic process of FPA inside air pressure greatly, but has no effects on the dynamic process of turning angle; moment of inertia and viscous damping coefficient have no effects on the dynamic process of FPA inside air pressure, but affect the dynamic process of turning angle greatly.

在弯曲关节模型推导的基础上，建立扭转关节的静态模型，并分析了扭转关节内腔压力，初始转角，橡胶管平均半径，橡胶管壁厚等参数对关节转角的影响，得出扭转关节的转动角度与充入FPA内腔的压缩气体压力之间基本呈线性关系，扭转关节的转角随初始角度和橡胶管平均半径的增大而增大，扭转关节的转角随橡胶管壁厚的增大而减小的结论；建立了扭转关节的动力学方程，仿真实验表明FPA的充放气过程与扭转关节的动力学过程相比时间极短，在实际系统设计和控制过程中可以忽略不计；分析讨论橡胶管壁厚，平均半径，初始角度，气体节流口面积，转动惯量，粘性阻尼系数等因素对扭转关节动态特性的影响，得出橡胶管初始壁厚的变化对扭转关节FPA内腔压力的动态响应几乎没有影响而对关节转角的响应曲线影响比较明显，壁厚较小时，关节可以得到较大的转角，并且转角的响应曲线没有超调，但上升时间长，壁厚较大时，关节转角变小，响应加快，但是有超调和轻微振荡现象，橡胶管平均半径越大，得到的关节转角越大，但是转角响应的超调量也随之增大，FPA的初始角度越大，关节的转角越大，并且超调量减小，振荡减弱，但是上升时间增大，管接头出口面积的大小对关节FPA内腔压力的建立过程影响较大，但对关节转角的动态响应几乎没有影响，转动惯量和粘性阻尼系数对FPA内腔压力的动态过程几乎没有影响而对扭转关节转角有较大影响等结论。

The results indicate that its dynamic stress-strain curve is hyperbolic type. The dynamic strain of LCES decreases with increasing confining pressure, cement content, curing ages and cyclic loading frequency when it is subjected to the same dynamic stress. At the same dynamic strain, the dynamic secant elastic modulus E_(sec of LCES increases and the damping ratio decreases with increasing confining pressure, cement content, curing ages and cyclic loading frequency. The curves ofσ_d～ε_d,E_～ε_d and D～ε_d with different EPS content intersect respectively, the trend of LCES deformation characteristic is inversely proportional to EPS content near the intersection. The value of dynamic strain at the intersection is about 0.5%~3.0%, the magnitude of which is related to the mixing proportions and confining pressure.

试验结果表明，LCES的动应力应变骨干曲线形态符合双曲线；在相同的动应力作用下，LCES产生的动应变随着固结压力、水泥掺量、试样养护龄期和振动频率的增大而减小；在动应变相同的情况下，随着固结压力、水泥掺量、试样养护龄期和振动频率的增大，LCES的动模量增大而阻尼比减小；随着加载次数的增大，LCES的动模量在开始阶段显著降低，然后趋于稳定，但当加载次数达到几百次时，动模量又有增大的趋势；不同EPS掺入比的LCES的动应力应变骨干曲线、动模量随应变变化曲线和阻尼比随应变变化曲线都发生了相交，交点前后EPS掺入比的大小对LCES动力变形特性的影响趋势是截然相反的，交点处的动应变值一般在0.5％～3.0％范围内变化，其大小与LCES的配比以及固结压力有关。

The thesis mainly includes: According to crane dynamic theory, established relevant dynamic model, and analyzed the dynamic properties of the bridge structure of the bridge crane, including the natural frequency, the model shape and the dynamic stress. A way to analyse the dynamic response of the bridge structure of the bridge crane which takes into account the dynamic properties of the steel rope pulley block has been explored successfully.

本文基于有限元理论和起重机动力学理论，以有限元分析软件ANSYS为平台，实现了计算机对钢丝绳系统和桥架的模态分析和瞬态动力学分析，得到的分析数据和结论对桥式起重机动态设计提供了有效的手段，论文主要内容包括：根据起重机动力学理论，建立了相关动力学模型，并对桥架结构进行动态性能分析（包括固有频率、振型以及动应力）的分析，探索出一种考虑钢丝绳滑轮组的动态特性在内的桥式起重机桥架结构动态应力分析的方法。

With the development of IT,the IT intra-industry will have higher demand about the software quality.this will absolutely attach importance to test of software.with the IT research and development and instrument,accompanying software engneering and software engneering practices further promotion,software test will be gotten more attention and specialized.the instruments will increase the progress of test,also can put the control and administration into the process of test.under the help of funtional test of data-driven of automatic test intruments,we can increase the coverage of the test,also can save more time and capital for corporations.because of continuous improvement of the process of software development,the continuous software integraton and automation of software test will be absolutely inevitable,also have more and more effects.different technology and research and development circumstances will have different requirements about how to automatize,so it hase more space deserved to research.

随着信息技术的不段发展，行业内对软件的质量要求越来越高，这必然引起对测试工作的重视，随着软件开发技术和工具的提高，软件工程和软件工程实践的推广，软件测试日益得到重视和专业化。工具能够加快测试的进度，可以把控制和管理引入整个测试过程。通过对自动化测试工具的数据驱动来进行功能性的测试，可以提高测试的覆盖率，并且可以为企业节省大量的时间和资金。因为软件开发过程的持续改进，软件项目的持续集成与测试自动化的发展是必然的，其作用也将越来越明显。不同的技术和开发环境对测试如何自动化有不同的要求，所以还有很多值得研究的地方。

The products samples came from Guangdong Entomological Institute. The test was made according to the national standards of the People's Republic of China (GB 15670-1995) in Toxicological Test Methods of Pesticides for Registration. SPF SD mice were used to made the peroral toxicity test and percutaneous toxicity test. There were ten mice (including 5 female rice and 5 male rice) in each group. New Zealand rabbits were used to make the eye irritation test and skin irritation test, with 4 rabbits in each test. FMMU albino guinea pigs were used to make the hypersusceptibility test, with 13-20 guinea pigs in each group.

方法］产品样品来源于广东省昆虫研究所，根据中国人民共和国国家标准GB15670-1995《农药登记毒理学试验方法》进行试验，试验使用SPF级SD大鼠，用于经口、经皮毒性试验，每组10只，雌雄各半；新西兰白兔，用于眼刺激和皮肤刺激试验，每试验4只；FMMU白化豚鼠，用于致敏试验，每组13~20只。

Is a production, sales agent service companies, Main Products and Services: constant temperature and humidity box; walk-in constant temperature and humidity room; salt spray test chamber; temperature shock test chamber; simulation of motor transport Test Units; Vibration Test Units; Units drop test; tensile testing machine; sclerometer; combustion test machine; electrical appliances and machine attachment test equipment; wire and cable and cable test equipment; microscopy; digital projector; image measuring instrument; coordinate measuring machine; voltage tester; Oscilloscopes; program-controlled variable frequency power supply; EMC instruments

惠尔仪器公司是一家集生产、代理销售为一体的服务性公司，主营产品和服务：恒温恒湿箱；步入式恒温恒湿室；盐雾试验箱；温度冲击试验箱；模拟汽车运输试验台；振动试验台；跌落试验台；拉力试验机；硬度计；燃烧试验机；电器产品附件及整机试验设备；电线电缆及连接线试验设备；显微镜；数字式投影仪；影像测量仪；三座标测量机；耐压测试仪；示波器；程控变频电源；EMC仪器等

The main products TQSW no local place-frequency electrical impulse voltage testing transformer test sets of series resonant frequency generator unit test transformer dry-type high-voltage testing transformer the ball-gap discharge frequency divider DC High-frequency DC generator, generator, inverter-current multi-function grounding impedance test system-current generator (up-flow device) performance of an integrated test bed Transformer Partial Discharge Detector mechanical properties of high-voltage switches Vacuum Tester Tester Tester Loop Resistance transformer capacity Tester-Load Switching Test Transformer tumor resistance measurement Transformer turns ratio tester tester MOA group tester insulating oil dielectric strength tester transformer loss parameter Intelligent Tester transformer loss-line parameter tester frequency interference dielectric loss dielectric loss tester anti-interference relay tester Ground Yin Xiaxian conduction tester cable fault tester tester tester generator rotor impedance large Grounding Resistance Tester Tester transformer features an integrated micro-moisture meter aperture automatic flash point tester Automatic Closed flash point detector vacuum oil filter boots pressure test device (automatic, semi-automatic) nuclear phase Instrument Series wireless digital core Instrument security tools relative to the mechanical properties testing machine clamp grounding resistance of grounding resistance measuring instrument digital megger digital high-voltage insulation resistance tester and a scalable high-altitude test tools, digital dual-phase volt-ampere facade sequence table clamp Three-phase Power Parameters Tester Calibrator lightning strike counter dedicated test wire, clamping insulation boards, pipe, cable tray mats polyimide film conductor line busbar electric appliances

扬州市苏博电气有限公司扬州市苏博电气有限公司主要产品有TQSW无局部放电工频试验变压器冲击电压发生器变频串联谐振试验成套装置试验变压器干式试验变压器高压分压器放电球隙中频直流发生器高频直流发生器变频大电流多功能接地阻抗测试系统大电流发生器变压器性能综合测试台局部放电检测仪高压开关机械特性测试仪真空度测试仪回路电阻测试仪变压器容量测试仪变压器有载开关测试仪变压器肿瘤电阻测试仪变压器变比组别测试仪氧化锌避雷器测试仪绝缘油介电强度测试仪变压器损耗参数智能测试仪变压器损耗线路参数综合测试仪变频抗干扰介质损耗测试仪抗干扰介质损耗测试仪继电保护测试仪接地引下线导通测试仪电缆故障测试仪发电机转子交流阻抗测试仪大型地网接地电阻测试仪互感器特性综合测试仪微量水分测定仪开口闪点全自动测定仪闭口闪点全自动测定仪真空滤油机绝缘靴耐压试验装置核相仪系列无线数字核相仪安全工具力学性能试验机钳形接地电阻仪接地电阻测量仪数字兆欧表数字高压绝缘电阻测试仪可伸缩高空测试工具数字双钳相位伏安表相序表三相电力参数测试仪雷击计数器校验仪专用测试导线，钳绝缘板，管，垫聚酰亚胺薄膜电缆桥架滑触线母线槽电热电器

Signalmen who have worked for more than one year and 70 new telegraph operators are subjected to Pattern Number Coding Ability Test, Ravens Progress Matrices, Memory Span Test, Distribution of Attention Test, Knocking Board Test, Choice Reaction Time Test, Action Speed Test, Action Stability Test, 16PF Test, Cornell Medical Index, SAS and SDS. hi the meanwhile their supervisors appraise the performance levels based on five grades from 5,4,3,2 and I .

研究对象为某军区工作1年以上的通信专业技术人员469名，另有作为预测效度检验的报训队新兵70名，分别接受图形数字编码能力测验、瑞文标准推理测验、记忆广度测验、注意分配测验、敲击板测验、选择反应时测验、动作速度测验、动作稳定性测验、卡特尔16PF测验、康奈尔测验、抑郁自评量表测验、焦虑自评量表测验；同时进行专业水平评价。

First, this paper presents three girders model with double cable planes which main girder and side girder is connected by rigid arms, analyzes the dynamic characteristic of Yonghe cable-stayed bridge and obtains its natural vibration modes (i.e., frequency, damping values and the mode shapes ) by ANLSIS structural analysis program and uses these parameters as dynamic dactylogram of the intact case of cable-stayed bridge. Using the passage of random as the ambient vibration ,the dynamic properties of Yonghe Bridge is measured and the modal parameter of its 15 years after is identified and used as dynamic dactylogram of the damaged case. By the finite element analysis and locale vibration test, damaged and undamaged modal parameter is analyzed and curvature mode shape, which is sensitive to damage state, is introduced as possible candidate for identifying and locating damage in the cable-stayed bridge. Selecting the branch of part measured point from modal parameter, this paper deduces the damaged index which can detect the possible damaged location of the cable-stayed bridge deck and identifies the damaged region and degree for Yonghe Bridge. For the purpose of structural condition monitoring in in-situ , from another viewpoint, this paper introduces the method called the best optimization vector to detect damaged location and degree. The accuracy and reliability of the method presented in this paper are demonstrated by static analysis and test and the healthy state of Yonghe Bridge can be evaluated.

建立了双索面通过刚臂与主梁及边梁相连的三梁式力学模型，采用ANSYS结构分析程序对永和斜拉桥进行动力分析，对其振动模态参数进行识别，以此作为斜拉桥完好状态下的动力&指纹&；采用自由交通流作为环境振源，对永和斜拉桥动力特性进行测试，识别出永和斜拉桥使用15年后的模态参数，确立了破损状态下的动力&指纹&；利用有限元分析、现场振动测试，对破损前后的模态参数进行分析，提取对破损状况较敏感的模态曲率作为斜拉桥破损诊断的参数；并从模态参数中选取部分点的分量，导出可以指示斜拉桥桥面大概损伤位置的Index损伤指标，识别出斜拉桥发生破损的区段及破损程度；考虑大型斜拉桥在线监测要求识别破损的具体位置，从另一角度提出采用最优矢量法具体确定破损发生的位置及程度；为验证本文研究成果，对永和斜拉桥进行静力分析及静力测试，对其健康状况提出可靠的评价。

Main business: CNC engraving machine Series: Applications: stainless steel, copper engraving Case insets processing; stainless steel, copper Case Shouban; spherical, Globoidal processing, text, sculpture ★ Case 5-axis double-headed insets engraving machine ★ Case 5-axis three insets engraving machine ★ Case 4-axis linkage double-headed insets engraving machine ★ Case 4-axis linkage three insets engraving machine ★ high triaxial strong double-headed die machine ★ high strength triaxial 3 Die machine ★ Case Drilling Machine, surface drilling machine ★ Case-meter pit, watches and clocks, glass-processing machine production testing of aircraft series:● test the waters Series: 10 automatic machine manually test the waters, six automatic Manual examination of water, really test the water leak-loaded needle ● Series: Semi-automatic assembly line of watches and clocks, watches and clocks, with three-pin CNC machines, semi-automatic machine ● single needle assembly Series: Semi-automatic cutting the core of machines, Case glass adhesive glue Machines, pneumatic pressure Digai ● strap-test: strap Rally torque testing machine, clasp switch testing machine, strap swing testing machine ● first test table: Table heading to the functional testing of aircraft, form the first vibration test machines, Table first parabolic dynamic testing machine has been with the German company Rexroth, Japan Yasukawa, Panasonic, Mitsubishi, and other well-known international companies have a long-term stability of technical cooperation, continue to study and absorb the advanced technology at home and abroad.

主营业务： CNC雕刻加工机系列：应用：不锈钢、铜表壳镶石雕刻加工；不锈钢、铜表壳手板；球面、弧面加工、文字雕刻★表壳五轴联动双头镶石雕刻机★表壳五轴联动三头镶石雕刻机★表壳四轴联动双头镶石雕刻机★表壳四轴联动三头镶石雕刻机★高强力三轴双头模具加工机★高强力三轴三头模具加工机★表壳钻孔机、表面钻孔机★表壳米坑位、玻璃位加工机钟表生产测试机系列：●试水系列：十头自动手动试水机、六头自动手动试水机、真水试漏机●装针系列：半自动钟表装配生产线、数控钟表装三针机、半自动单针机●装配系列：半自动切把芯上的机、表壳玻璃胶水粘接机、气动压底盖机●表带测试：表带拉力扭力测试机、表扣开关测试机、表带摇摆测试机●表头测试：表头按的功能测试机、表头震动测试机、表头抛动测试机一直以来，公司与德国Rexroth、日本安川、松下、三菱等国际知名企业有着长期稳定的技术合作，不断地学习和吸收国内外的先进技术。

Looking to bounce back from defeat against Cesena last weekend, the Calabrian boss will be sticking to his tried and tested 4-3-3, with Lopez and Sedivic joined up front in Giampaolo's absence by either Nanni or Plasmati.

鉴于上周末对切塞纳的比赛中反败为胜，这支南方球队将会更坚持其一贯而有效的4-3-3阵型，洛佩斯和塞德维奇将取代受伤缺席的詹保罗，和纳尼或者帕斯马蒂中的一个搭档锋线。

Meanwhile, their exposure to the more freewheeling ways of the West broadened dramatically.

另外，西方较自由的生活方式对年轻人的影响增大。