查询词典 dynamic friction

Available test results and calculations include tear, static and dynamic coefficient of friction, average peel/tear, load displacement at first peak, energy at first peak, energy between limits, peel length and more.

提供的试验结果及计算包括：撕裂、动态和静态摩擦系数、剥离/撕裂平均值、第一个峰值处的载荷和位移、第一个峰值处的能量、极限之间的能量、剥离长度等。

The coefficient of friction for static contact is higher than for dynamic contact, so static contact provides better traction.

此时因为静摩擦系数比动摩擦系数高，所以静摩擦的附着力较大。

The nonlinear Winkler-Kelvin sub-grade model is adopted in this simplified model and the complicated 3-D problems of the soil-single piles dynamic interaction are simplified to the 1-D, that is to say, the lateral nonlinear acting force of the soil to the pile shift is simulated with thehorizontal nonlinear springs which have the continuous uniform distribution, while the nonlinear spring restoring force is described by the deteriorated Bouc-Wen model; the radiation damping and material damping due to the energy dissipation and inner friction in the soil are displayed with the dashpots which are in parallel with the horizontal nonlinear springs.

该模型采用非线性Winkler-Kelvin地基模型，将复杂的地基土-单桩动力相互作用的三维问题，简化为一维问题，即，地基土对桩轴的横向非线性作用力，由随深度均匀分布的水平非线性弹簧模拟，非线性弹簧恢复力由退化的Bouc-Wen模型描述；地基土中由于能量耗散和内部摩擦而产生的幅射阻尼和材料阻尼，由与水平非线性弹簧并联的粘壶表示。

This work employs operator-splitting method / finite element method to study dynamic performance and the stability of liquid-lubricated herringbone grooved journal bearing with micro-polar lubricants. Load capacity, friction resistance, stiffness/damping coefficients and critical rotor mass were investigated.

本文采用算子分裂/有限元法计算微极性流体润滑剂的螺旋槽径向轴承承载力、粘性阻力、润滑油膜刚度系数和阻尼系数等特征量，研究轴承的动力特性和稳定性问题。

Such as leakage of smaller, more dynamic or static ring ring ring problems; leakage is large, then the dynamic and static friction between the ring problem.

如泄漏量较小，多为动环或静环密封圈存在问题；泄漏量较大时，则表明动、静环摩擦副间存在问题。

Leakage such as smaller, more dynamic or static ring ring ring problem exist; leakage is large, then the dynamic and static friction between the ring problem.

如泄漏量较小，多为动环或静环密封圈存在问题；泄漏量较大时，则表明动、静环摩擦副间存在问题。

Through simulates between the mold and the sheet dynamic contact accurately, contacts the boundary dynamic change in the comprehensive analysis sheet and the mold in the foundation, unified the ANSYS software to give the model geometry description, the contact algorithm choice, the contact friction model establishment and so on the concrete method.

通过准确地模拟出模具与板料之间的动态接触，在全面分析板料与模具接触边界动态变化的基础上，结合ANSYS软件给出了模型的几何描述、接触算法选择、接触摩擦模型的建立等具体方法。

Leakage in the initial observation to determine the basis of the leakage site, and then manually set car observation, if the leakage were no significant changes in static and dynamic sealing ring problem; such as the disk when there are significant changes in leakage can be concluded that the dynamic , static friction ring problems; such as leakage of medium along the jet axis, while moving most of Central ring problems, leakage to the surrounding medium or from the water spray cooling holes in the leakage, the seal ring for static failure.

在初步观察泄漏量、判断泄漏部位的基础上，再手动盘车观察，若泄漏量无明显变化则静、动环密封圈有问题；如盘车时泄漏量有明显变化则可断定是动、静环摩擦副存在问题；如泄漏介质沿轴向喷射，则动环密封圈存在问题居多，泄漏介质向四周喷射或从水冷却孔中漏出，则多为静环密封圈失效。

Leakage in the initial observation to determine the basis of the leakage site, and then manually set car observation, if the leakage were no significant changes in static and dynamic sealing ring problem; such as the disk when there are significant changes in leakage can be concluded that the dynamic , static friction ring problems; such as leakage of medium along the jet axis, while moving most of Central ring problems, leakage to the surrounding medium or from the water spray cooling holes in the leakage, the seal ring for static failure.

在初步察看泄漏量、断定泄露部位的基本上，再手动盘车视察，若泄漏量无显明变更则静、动环密封圈有问题；如盘车时泄漏量有显著变更则可判断是动、静环摩擦副存在问题；如泄漏介质沿轴向喷射，则动环密封圈存在问题居多，泄漏介质向四周喷射或从水冷却孔中漏出，则多为静环密封圈失效。

Leakage in the initial observation to determine the basis of the leakage site, and then manually set car observation, if the leakage were no significant changes in static and dynamic sealing ring problem; such as the disk when there are significant changes in leakage can be concluded that the dynamic , static friction ring problems; such as leakage of medium along the jet axis, w你好le moving most of Central ring problems, leakage to the surrounding medium or from the water spray cooling holes in the leakage, the seal ring for static failure.

杂质泵安装静试时泄漏机械弥缝安装调试好后，一般要进行静试，察看泄漏量如泄漏量较小，多为动环或静环弥缝圈存在问题；泄漏量较大时，则表白动、静环磨擦副间存在问题在开端察看泄漏量、判断泄漏部位的根蒂根基上，再手动盘车察看，若泄漏量无明显变化则静、动环弥缝圈有问题；如盘车时泄漏量有明显变化则可下定论是动、静环磨擦副存在问题；如泄漏介质沿轴向喷洒，则动环弥缝圈存在问题居多，泄漏介质向四周喷洒或从水冷却孔中漏出，则多为静环弥缝圈失效此外，泄漏通道也可同时存在，但一般有主次区分，只要察看细致，认识结构，一定能正确判断

The absorption and distribution of chromium were studied in ryeusing nutrient culture technique and pot experiment.

采用不同浓度K2CrO4(0，0.4，0.8和1.2 mmol/L)的Hoagland营养液处理黑麦幼苗，测定铬在黑麦体内的亚细胞分布、铬化学形态及不同部位的积累。

By analyzing theory foundation of mathematical morphology in the digital image processing, researching morphology arithmetic of the binary Image, discussing two basic forms for the least structure element: dilation and erosion.

通过分析数学形态学在图像中的理论基础，研究二值图像的形态分析算法，探讨最小结构元素的两种基本形态：膨胀和腐蚀；分析了数学形态学复杂算法的基本原理，把数学形态学的部分并行处理理念引入到家实际应用中。