查询词典 dsp

In the paper,using three methods,including C language,Matlab and DSP Builder,producing the arbitrary waveform initialization data of the sine wave,the triangular wave,the saw-tooth wave and the square-wave.Programming,parameter setting and waveform simulation are described to every method detailedly.

DDS系统一般包括系统时钟、频率预置与调节电路、相位累加器、ROM查找表，输出的数据通过外接的D/A转换器和滤波器完成波形输出。

This thesis from the angle of signal detection, first theoretically gives out a RFOG closed signal detection design based on DSP. The signal detection system mainly includes related detection. signal conversion and the formation of feedback saw tooth. Related detection must guarantee signal synchronization sampling, and get the biggest signal noise ratio.

本文首先分析了谐振式光纤陀螺的基本原理和系统结构，并从信号检测的角度出发，从理论上给出了一个基于DSP实现的谐振式光纤陀螺的闭环信号检测方案，信号检测系统主要包括相关检测，信号的转换和反馈锯齿波的形成。

This paper shows the discussion how to make use of the advanced DSP technology to design the flying saw machine control system,including the hardware circuits and software flowchart.

探讨了将先进的DSP技术应用于自动跟踪定尺飞锯机控制系统，设计其硬件电路及软件流程。

The system is built in the VC++6.0 environment on the basis of PC flat roof, DSP locomotion control card and relevant drivers. Its software design can be reconstructed based on the modularized function block technology, and thus a modularized STEP-NC Milling system is built.

在Visual C++6.0环境下，以PC平台、DSP运动控制卡及相应的驱动器为基础，基于功能块技术的模块化可重构软件设计，建立模块化的STEP-NC铣削数控系统。

And a certain degree of DSP development of the ability to drive the bottom.

并且有一定的DSP底层驱动开发能力。

All the algorithms should be realized in GPS user DSP chip.

本文讨论了非差相位精密单点定位用户端的程序实现问题。

Independent DSP Inputs Vote the Best Voice or Data Channel.

独立的DSP输入信号，比选最佳话音或数据通道

A very low frequency and low bit-rate digital communication systems to achieve program, which mixed in the software programming method is to use DSP hardware implementation, the article gives the ...

介绍了一种甚低频低码率数字通信系统的实现方案，该方案中的软件采用混合编程的方法，硬件则用DSP实现，文章给出了整个。。。

A very low frequency and low bit-rate Digital Communication System program, which mixed in the software programming method, the hardware is realized with DSP, the article gives the ...

介绍了一种甚低频低码率数字通信系统的实现方案，该方案中的软件采用混合编程的方法，硬件则用DSP实现，文章给出了整个。。。

A digital voice communication system to achieve】 DSP programming, subroutines, very low frequency, debugging, hardware and software ...

一种数字语音通信系统的DSP实现】编程，子程序，甚低频，调试，软硬件。。。

Finally it offers the analysis of the fault-tolerance system as well as its test verification.

这样，运行于空间环境中的系统的设计目标就是在保证系统实时性

However, it is still difficult to find out the real reason of the increase of the keratinized gingiva during the orthodontic extrusion whether it is due to the proliferation of the gingival tissue or to its elastic nature, that is because the proliferation of the fibroblasts as well as the connective tissue changes in volume and the intra-fibers spaces were all immeasurable in most of the studies.

然而，仍然难以找到真正的原因增加的角化牙龈在正畸挤压它是否是由于扩散的牙龈组织或其弹性性质，这是因为增殖的成纤维细胞以及作为结缔组织的变化量和内部纤维空格都是不可估量的，大多数的研究。