查询词典 driving gear

Equipped amidships for a lower center of gravity is a 3-speed transmission allowing gear changing and realistic low speed driving.

舯配备了低重心是一家三高速传输让换档和现实的低速驾驶。

By considering torque characteristics of variable-frequency motors and mesh stiffness as well as backlash nonlinearity in gear transmission,a dynamics model for the cutting system of shield tunneling machine with redundant drives was established. The fluctuation characteristics of torque loads and dynamic cutterhead driving torque in composite strata were analyzed.

复合地层掘进扭矩载荷突变是造成盾构机掘进过程中堵转停机的直接原因，考虑盾构机刀盘驱动变频调速电机特性、转矩传递过程中齿轮啮合刚度及齿侧间隙等非线性因素，建立冗余驱动的盾构机刀盘切削系统机电耦合动力学模型；针对典型复合地层地质条件，对盾构机在上软下硬地层掘进过程中刀盘驱动转矩动态特性进行仿真分析。

Hurry clan pace of life is always in a state of high-speed operation, it is like driving, always use fourth gear high gear in advance ...

匆忙 族的生活节奏永远处于高速运作的状态，就好似开车时，总是用四档高速档在前进。。。。

The upper and lower unit open them one by one driving surface cover plate, double-check the drum gear and roller drive gear for the work of

末了不兵上下单位传动背的盖板一一敞开，澈底查抄滚筒传动齿轮和墨辊传动齿轮的处事环境

The rattling model of a one stage gear system is established,in which mass unbalance,speed fluctuation of driving shaft and backlash of the gear pair are considered.

在考虑不平衡质量、主动轴转速波动及齿侧间隙的情况下，建立了单级齿轮传动系统的拍击振动模型。

Considering the torque fluctuation of the driving shaft and the existence of the backlashes in both gear pair and clutch, a lumped mass gear- rattling model is established.

在考虑主动轴驱动转矩波动、齿轮副齿侧间隙及离合器间隙的情况下，建立了同时含有离合器间隙和齿侧间隙的齿轮传动系统拍击振动分析的集中质量模型。

The build-up welding of the meshing surfaces of big gear wheels :During operations of the big driving gears of big rolling mills and squeezers, the meshing surfaces wear easily and form cavities due to the squeezing force and attrition with the thinning of the gears resulting in the rejection of the gear wheels.

大齿轮咬合面堆焊：大型轧机和压榨机的传动大齿轮在工作过程中，齿的咬合面产生大的挤压力和磨擦力易磨损和形成凹坑，齿厚减薄，因而报废。

The universal powder box includes one box with powder bin and cover, one stirrer inside the powder bin, one powder feeding roller in the outlet of the powder bin, one developing roller contacting with the powder feeding roller and one locking device for the powder box to be set in and taken out from the sensitive drum. The cover has one upper planar surface, and after being installed, the plane is located below one corresponding raised edge of the printer. In the roller end gear combination outside one side wall of the box, there are two with driving force driving position.

包括一个带有粉仓的盒体和盖，位于粉仓内的搅拌装置，一个位于粉仓出口处的送粉辊、一个与送粉辊接触的显影辊，及使粉盒能顺利置入或取出感光鼓盒的锁放装置，盖的上表面基本是一个平面，装机后该平面位于打印机对应盖下表面凸起的下缘之下，在盒体一个侧壁外的各辊端齿轮组中，有两个带有动力受口的驱动位。

Using isothermal an nealing technology for gear forging stocks is an effective way of improving the gear driving accuracy. Explains in detail the isothermal annealing process, features and equipments necessary for the heat treatment.

认为采用齿坯等温退火工艺是提高齿轮传动精度的有效途径，详细介绍了等温退火工艺原理和工艺特征，还介绍了该热处理过程采用的设备。

By contrasting and analyzing of various take-ups on belt conveyor . This design is mainly about automatic windlass tension station . Its drive part makes up into worm pair and gear driver . Windlass uses worm gear worm driving reel which binds wire rope to pull tight adhesive tape . In the meantime , it adopts the frequency conversion adjusting speed motor to control tensioning force .

通过对带式输送机各种拉紧装置的比较和分析，本设计主要是自动绞车式张紧装置的设计，其传动部分由蜗轮蜗杆传动和一对开式齿轮传动两部分组成，绞车用蜗轮蜗杆传动带动卷筒来缠绕钢丝绳，从而拉紧胶带，同时采用变频调速电机对张紧力进行控制。

Prima rily, the prime crimina l's crime has nothing to do with lime and overtime.

首犯的犯罪基本上与石灰和加班无关。

Some would fail and some would prosper,some would die and some would kill,some would thank the Lord for their deliverance, and some would curse John Sutter's Mill.

有人无功而返，有人心遂所愿；有人长眠异乡，有人图财害命；有人将感激上帝解脱了他们，有人会诅咒约翰萨特的磨房。