查询词典 driving circuit

The Periscope Drawtube will be bent because of the water resistance in sailing and this bend will cause the error of star measurement. Due to its especial structure, contactless measurement is the only way to measure its bend degree. First this paper introduces the method by linear array CCD based on structure and light path; Second it expatiates linear array CCD work principle and driving scheduling with example of TCD1501C and the driving circuit by CPLD. The output signal of linear array CCD includes common disturbance so the differential amplifier is needed. In order to make the signal adapt to computer processing, a threshold circuit with Schmitt characteristic and the data process following threshold are given. At last, some key problems in application are given.

潜艇潜望镜的镜筒在航行时受到水的阻力会产生弯曲变形，这种变形会造成潜艇对星体测量的误差；由于镜筒结构的特殊性，对其弯曲程度的测量只能采用非接触方法；首先从结构和光路方面介绍采用线阵CCD作为检测元件实现对镜筒弯曲程度的测量；其次以东芝公司的线阵CCD（TCD1501C）为例阐述了其工作原理及驱动时序的控制要点，并介绍了基于可编程逻辑器件的线阵CCD的驱动电路；线阵CCD输出的信号中含有共模干扰，必须采用差分放大器将其抑制；为将信号转化为适合计算机处理的数字信号，文中给出了有一定实用价值具有施密特特性的二值化处理电路及二值化后的数据处理过程；最后阐述了在实际使用中的一些关键问题。

The computer separately connects and controls the I/O end and A/D converter; the I/O end connects and controls the X, Y axis driving circuit and the semiconductor laser; the X, Y axis step-by-step driving circuit connects and controls the X, Y step-by-step electrical machines to control the dimensional platform; the beam of the semiconductor laser passes through the focusing drawtube with 0.1mm diameter to form the facula with the diameter less than 0.1mm; the facula irradiates on the detector surface of the XY dimensional displacement platform to produce the corresponding electric signals; the detector surface connects the A/D converter through the amplifier; the electrical signal is amplified and is converted into the data signal by the A/D converter and is sent to the computer for processing.

由计算机分别连接并控制I/O端口和A/D转换器，I/O端口分别连接并控制X、Y轴步进电机驱动电路和半导体激光器，X、Y轴步进电机驱动电路分别连接并控制X、Y轴步进电机，从而控制二维位移平台，半导体激光器的光束经过设有直径0.1mm小孔的聚焦镜筒形成＜0.1mm直径的光斑，光斑照射于设在XY二维位移平台上的探测器表面使其产生响应的电信号，探测器表面经放大器连接A/D转换器，电信号经放大器放大后，由A/D转换器转换为数据信号送计算机处理。

What this paper finished mainly work as follows: Five-phase hybrid step motor driver system with fixed-chopping frequency and constant total current driving is fully described. Mathematical model of the system, included the current control circuit, power driving circuit and five-phase hybrid stepping motor is established. The steady modeling of the system is established and studied. Based on the steady modeling of the system, dynamic modeling of the system is studied and single step response characteristic is constructed with MATLAB/Simulink. The simulation results, which is certified by the theory analysis, coincide with the theory analysis.

本文主要完成的工作包括几个方面：对五相混合式步进电动机恒频斩波恒总流驱动系统进行了完整的描述；建立了包括电流控制电路、功率驱动电路以及五相混合式步进电动机在内的恒频斩波恒总流驱动系统的完整的数学模型；基于MATLAB/Simulink建立了恒频斩波恒总流驱动系统稳态仿真模型，并进行了仿真；在建立其稳态仿真模型的基础上，对动态模型进行研究，并借助于MATLAB/Simulink工具建立了恒频斩波恒总流驱动系统单步响应特性的仿真模型并对其单步响应特性进行了仿真研究，仿真结果与理论分析相符。

The controller includes multi-channel switching circuit, interface and conversation circuit, input and output circuit, manual button control circuit, LCD driving circuit, real-time clock circuit, preparedness store circuit, keyboard processing circuit and dial switch circuit.

该控制器硬件包括多通道切换电路、接口及转换电路、输入输出电路、手动按钮控制电路、手动与自动切换电路、液晶显示驱动电路、实时时钟电路、预案存储电路、键盘处理电路、拨码开关电路。

The chip consists of a power mos, mode select circuit, driving circuit, and two series of controller circuit. The controller consists to the active current sensing circuit, sample and hold circuit, hysteresis current comparator, voltage to current converter, error amplifier and non-overlap circuit.

晶片包含一组功率电晶体、模式选择电路、驱动电路及二组控制电路，控制电路主要架构有主动式电流感测电路、取样保持电路、磁滞电流比较电路、电压对电流转换电路、误差放大器及非重叠电路。

The electro-optical device includes, in a peripheral area, image signal lines which run from an external circuit connection terminal to a sampling circuit detouring a periphery of a data line driving circuit, and a vertical conducting terminal which is laid in a second side of the TFT array substrate intersecting the first side in the peripheral area observed from the sampling circuit and which electrically conducts to a counter substrate.

电光装置，在周边区域具有从图像信号端子迂回绕过数据线驱动电路的周围而到达采样电路的图像信号线和在周边区域中从采样电路看在与第1边相邻的一个基板的第2边附近配置的、实现与另一基板侧的电的上下导通的上下导通端子。

When we design the IPM circuit ,we should design such main sections:the driving circuit , the buffer and absorption circuit , the protection circuit.

IPM电路设计主要包括驱动电路部分、缓冲吸收电路部分以及保护电路部分。

This paper will emphasize on analyzing these two problems, and make a driving board with TLP250, this driving circuit can drive four IGBTs.and its driving signal is produced according to the requests, each driving signal is separated rightly with only one power supply, this circuit can also prevent from overflowing or short-circuit and keeping bridge arm from connecting directly.

本文将着重分析这两个问题，并利用TLP250设计了一块模块驱动板，此板可以驱动四个IGBT。此板的驱动信号符合要求，每路驱动信号在电位上是隔离的，而输入电源只有一个，该电路还有过流或短路保护功能以及防止桥臂直通的功能。

Also, we select the signal collecting circuit of three output polars, the coupling circuit using capacitance and resistance, the alternating amplify processing circuit, the positive feedback retardation comparsion, the driving circuit of output current and the stabilization voltage supply circuit.

选择了InSb磁阻三端输出型信号采集电路，阻容耦合型交流放大电路，正反馈迟滞型电压比较器和大电流推挽驱动电路及稳压电源电路。

The hardware circuit is made up by microcomputer controlling circuit, motor driving circuit, wire-feeding speed regulating circuit, arc welding power source main circuit, as well as the isolating, sampling, welding state identification circuit.

硬件电路由单片机控制电路、电机驱动电路、送丝调速电路、弧焊电源主电路以及隔离、采样、焊接状态识别电路构成。

Singer Leona Lewis and former Led Zeppelin guitarist Jimmy Page emerged as the bus transformed into a grass-covered carnival float, and the pair combined for a rendition of "Whole Lotta Love".

歌手leona刘易斯和前率领的飞艇的吉他手吉米页出现巴士转化为基层所涵盖的嘉年华花车，和一双合并为一移交&整个lotta爱&。

This is Kate, and that's Erin.

这是凯特，那个是爱朗。