查询词典 drive shaft

As a result, we from the host to the chain drive auxiliary engine has detected that the fitting with the feidahong of the cardan shaft section.

于是，我们从主机到副机的链传不静不休，不断查抄到与飞达脚拆开的万向轴节。

End drive – usually means a cardan shaft is connected to the component through an adapter (can be quick-fit).

末端驱动—通常指通过一个适配器连接到一个推进轴。

Power of motor is convected to gearbox through belt , and after slowdown and increase torsion, the power is passed to the main shaft of the disc and drive it to rotate.

电动机的动力通过皮带传送给变速箱，经变速箱降速增扭后，将动力传给制粒圆盘主轴，带动制粒圆盘旋转。

Most truck power take offs are arranged so that the vehicle's clutch disengages not only the main transmission's output shaft to the drive wheels, but also disengages the PTO.

大多数卡车权力采取平衡的安排，使车辆的离合器分离不仅主传动的输出轴的驱动车轮，而且还脱离接触的动力输出。

Note that the drive is transmitted from crank shaft to big wheel by vertical shafts and bevel gearing.

请注意，驱动器是由曲轴，以大车轮由竖井和锥齿轮。

First ,make up the main parts'structure and the key designing parameters; thus reference to the similar driving axle structure , decide the entire designing project ; fanially check the strength of the axle drive bevel pinion ,bevel gear wheel , the differentional planetary pinion, differential side gear , full-floating axle shaft and the banjo axle housing , and the life expection of carrier bearing .

本文首先确定主要部件的结构型式和主要设计参数；然后参考类似驱动桥的结构，确定出总体设计方案；最后对主，从动锥齿轮，差速器圆锥行星齿轮，半轴齿轮，全浮式半轴和整体式桥壳的强度进行校核以及对支承轴承进行了寿命校核。

Traditional worm casting ladle is adopt to the lower light revolving shaft, before pouring, molten iron is self dumping, using self-locking of worm gear, control dumping torque of casting ladle, pouring later, man turn on hand wheel, bevel gear turn to worn gear drive, and turn casting ladle pouring, don't turn on hand wheel, another side of worm gear tooth self-locking, control vertical torque of casting ladle.

传统蜗轮浇包都是采用较低的轻便转轴，浇注前期，铁水自己倾倒，利用蜗轮的自锁性，控制浇包的倾倒力矩；浇注后期，人扳转手轮，伞齿轮转向蜗轮传动，翻转浇包浇注，不扳动手轮时，蜗轮齿的另一侧面自锁，控制浇包的竖直力矩。

At present, we are able to provide such motorcycle parts as chain wheel, chain, brake shoe, clutch cover, ignitor, rectifier, relay, high pressure bag, magnetic motor coil, belt, shock absorber, moulding, air valve, valve guide, camshaft, timing chain, spark plug, rocker arm, piston, piston ring, start disc, bearing, oil tank cover, lock set, steering bearing, oil meter, filter, horn, drive plate, driven wheel assembly, buffer rubber, intermediate shaft sleeve, starter motor, spoke and switch button etc.

目前，本公司有以下多个摩托车系列：链轮、链条、制动蹄、离合器压盘点火器、整流器、继电器、高压包、磁电机线圈、皮带、减震器、压条、气门、导管、凸轮轴、时规链、火花塞、摇臂、活塞、活塞环、启动盘、轴承、油箱盖、套锁、转向轴承、油量计、滤清器喇叭、驱动盘、从动轮总成、缓冲胶、中轴套、启动电机、辐条、开关按纽等。

Torque control mechanism: Uses the worm bearing adjuster axial to flee moves, on the worm shaft is loaded with the small dish reed, flees the worm bearing adjuster axial moves through the crank drive to the torque axis, again touches the switch through the cam the principle.

4转矩控制机构：采用蜗杆轴向窜动，蜗杆轴上装有碟簧、把蜗杆的轴向窜动通过曲柄传动到转矩轴，再通过凸轮触动开关的原理。

By driving method in two ways:(1) mechanical, engine mounted on the outer cylinder by the gas distribution on the eccentric cam shaft wheel drive, the use of oil-absorbing membrane produced, oil pressure role in the fuel pump with hand-arm lower end, when the gasoline engine does not work, can be used to pump oil.

按驱动方式分两种：（1）机械式，装在发动机缸体外侧，由配气凸轮轴上的偏心轮驱动，利用膜片产生吸油、压油作用，在汽油泵下端装有手动臂，当汽油机不工作时，可用来泵油。

The absorption and distribution of chromium were studied in ryeusing nutrient culture technique and pot experiment.

采用不同浓度K2CrO4(0，0.4，0.8和1.2 mmol/L)的Hoagland营养液处理黑麦幼苗，测定铬在黑麦体内的亚细胞分布、铬化学形态及不同部位的积累。

By analyzing theory foundation of mathematical morphology in the digital image processing, researching morphology arithmetic of the binary Image, discussing two basic forms for the least structure element: dilation and erosion.

通过分析数学形态学在图像中的理论基础，研究二值图像的形态分析算法，探讨最小结构元素的两种基本形态：膨胀和腐蚀；分析了数学形态学复杂算法的基本原理，把数学形态学的部分并行处理理念引入到家实际应用中。