查询词典 drill rod

This article uses magnetism examination the method, to drill rod collar whether arrives conducts the research.

本文采用磁检测的方法，对钻杆接箍是否到位进行研究。

Drill rod collar position detector set hardware circuit design In the petroleum drilling process, the ejection controller played the seal well head role.

钻杆接箍位置检测装置硬件电路设计摘要：在石油钻探过程中，防喷器起到了密封井口的作用。

The three fail form of scoring,fillister and corrosion for 127 mm(5) S135 drill rod joint ,corrosion rate and corrosion production have been researched by means of analysis of chemical composition and microstructure,testing of mechanical property.

通过化学成分分析、力学性能测试、组织结构分析和高温高压模拟试验，对127 mm(5)S135钻杆接头内壁出现划痕、凹槽和腐蚀三种失效形式，钻杆的腐蚀速率和腐蚀产物进行分析研究。

In order to ensure the integrity of rock carvings, the construction team had to take the original Canadian mechanized off hilltops Act, in the grotto of the left foot attached to the thickness of the rock, the rock drilling machine with internal combustion engines, compressed air rock drill holes in the parent rocks on the hit row, and then by hand drill rod of the ways to split the rock.

为了保证雕刻岩体的完整性，施工队不得不采取原始加机械化的劈山法，在留足石窟所依附的岩体厚度后，用内燃机凿岩机、压缩空气凿岩机在母岩上打排孔，然后用人工打钢钎的方法把岩石劈开。

The experiment study about the subcritical normalizing holding temperature effects the macrostructure and hardness of the 40SiMnCrNiMoA steel shows: When subcritical normalizing holding temperature is 760℃, the ferrite in the mixture phase structure is lumpish, the hardness of the steel is low (about HRC32), and when the holding temperature is over 800℃, the hardness of the steel is about HRC49, the ferrite in the mixture phase structure is in old critical range austenite grain boundaries, it is disadvantage for the steel strengthening. When the holding temperature is 780℃, the mixture phase structure is mixture phase structure including the strip ferrite、martensite and bainite, the ferrite is less than 20%wt, its grains are fine and even, the hardness of the steel is about HRC38, it is in the range of HRC35-40 which is the long-life drill rod needed.

亚温正火温度对40SiMnCrNiMoA的组织和硬度等性能的影响的实验研究表明，当亚温正火保温温度为760℃时，复合组织中的铁素体形态是块状，处理后的材料硬度相对较低（HRC32左右）；而当采用大于800℃温度亚温正火处理，材料硬度为HRC49左右，组织中铁素体大部分较连续地存在于原奥氏体的晶界，对材料强化不利；当40SiMnCrNiMoA钢780℃亚温正火后，硬度为HRC38左右，在以往小钎杆较长寿命所需硬度范围HRC35-40内，而组织为细条状铁素体+以板条马氏体和条状无碳贝氏体为主的复合组织，晶粒细小均匀，铁素体体积含量少于20％。

They are the strengthening-toughening of 40SiMnCrNiMoA by the critical normalizing, the fine macrostructure and property matching between the all drill rod parts, the low tendency of decarburizing and delete the weak inner hole surface owe to the drill-hole and hot-rolled with core process of rolling steel.

本文研究表明，40SiMnCrNiMoA钢亚温正火强韧化特性、亚温正火使钎杆整体性能良好地匹配、较小的脱碳倾向和钻孔法消除钎杆内孔粗糙和脱碳表面是钻孔法并整体780℃亚温正火+钎柄淬火和低温回火的H22-40SiMnCrNiMoA锥体连接小钎杆延寿的主要原因。

With the increase of borehole depth, the comparative advantage of hydraulic top-drive core drill decreases. In this case, the length of drill rod stand should be increased to improve efficiency of round-trip operation.

钻孔深度加大后，动力头钻机在钻进施工效率方面的对比优势会逐渐减弱，应该考虑采取加大钻杆立根长度，从而加大起下钻速度的措施。

Comparing the quality of the three methods of making hollow drill steel,"drill-hole and hot-rolled with core"method is best. The present paper indicates that the prolonging life mechanisms of the new drill rod include four aspects.

本文给出H22-40SiMnCrNiMoA锥体连接钎杆制造工艺，运用&钻孔-带芯热轧法&、&热穿-热拔法&、&热穿-热轧法&三种工艺加工的H22-40SiMnCrNiMoA试验钎杆中，&钻孔-带芯热轧法&各方面的质量都是最好。

The fatigue life of the newly developed drill rod is also predicted according to the S-N curve of drill steel and its theoretical loading spectrum.

同时，结合材料的S-N曲线和钎杆的理论载荷谱，运用电算程序，预估了新型结构钎杆的抗疲劳寿命。

Because of long and thin structure characteristics, and sustain high frequency impact load under erosive medium, the drill rod's serve condition is most rigorous, and drill rod is one of the most easily damage tool in the percussion drilling rock system.

由于细长的结构特征和在腐蚀性介质中承受高频冲击载荷，使钎杆成为服役条件最苛刻、在冲击式凿岩系统中最容易损坏的机件，钎杆寿命低是制约凿岩爆破技术进步的关键问题。

In the negative and interrogative forms, of course, this is identical to the non-emphatic forms.

。但是，在否定句或疑问句里，这种带有"do"的方法表达的效果却没有什么强调的意思。

Go down on one's knees;kneel down

屈膝跪下。。。下跪祈祷