查询词典 drawing-room

The large banded structures would lead to break during drawing.The intermidiate ones would result in extensible crack but not result in break during drawing.The small ones could exist inside the wire in the form of incontinuous particulates,resulting in a decrease of the p...

粗大的带状组织将直接导致拉丝断裂；稍小一点的带状组织不会引起拉丝断裂，但在钢丝内部存在着明显的非稳态扩展裂纹，是不安全的；细小的带状组织不会引起拉丝断裂，最终将以断续的点状形态存在于成品钢丝中，但对其安全性存在重大隐患。

The large banded structures would lead to break during drawing. The intermidiate ones would result in extensible crack but not result in break during drawing. The small ones could exist inside the wire in the form of incontinuous particulates, resulting in a decrease of the performance of wire.

粗大的带状组织将直接导致拉丝断裂；稍小一点的带状组织不会引起拉丝断裂，但在钢丝内部存在着明显的非稳态扩展裂纹，是不安全的；细小的带状组织不会引起拉丝断裂，最终将以断续的点状形态存在于成品钢丝中，但对其安全性存在重大隐患。

The fracture reasons of high strength PC steel wire are analyzed, it's considered that center segregation, central cavitation, poriness and inclusion are the metallurgical reasons which lead to the facture of PC steel wire and in the rolling process, differential coping quality, microcrack caused by surface defect, abnormal microstructure caused by burnt and improper cooling velocity, the ears on the head of the wire, overlapping of the wire rod itself are the main reasons which lead to the facture of PC steel wire. At the same time, inappropriate pickling, differential phosphorization quality, the bad heat treatment quality, the generation of crack in the improper drawing and transverse crack caused by abnormal laying of the drawing die are also the reasons of the cracking of PC wire.

对高强度PC钢丝断裂原因进行了分析，认为连铸坯的中心偏析、中心缩孔、疏松和夹杂是导致PC钢丝断裂的冶金原因；轧制过程中，较差的修磨质量、表面缺陷导致的微裂纹，过烧以及不适当的冷却速度导致的非正常显微组织，盘条头部的耳子、盘条本身折叠是导致PC钢丝断裂的主要原因；同时，不恰当的酸洗、较差的磷化及热处理质量、不适当拉丝裂纹的产生、拉拔模具安放不正导致的横裂也是PC钢丝断裂的原因。

The paper describes how to raise the service efficiency of 6502SYS electric interlocking design software based on the relevant improvements made for protrudent problems with 6502SYS electric interlocking design software under DOS operating system, and introduces the graphics generation of drawing script by using VB macro of Microsoft Excel and AutoCAD 2004 drawing software.

本文针对在DOS操作系统下的6502SYS电气集中设计软件在一些方面存在的突出问题，做出了相应的改进，论述了如何提高该软件的使用效率，并介绍了使用&Excel电子表格软件&中的VB宏的方法和利用&AutoCAD2004制图软件&解决绘图脚本的图形生成等问题。

The shape formed by projection of correlation line of rotative surface on which two axises Intersect by meahs of analytical method is discussed,and some related characterlstles of hyperbolic curve ,on the basis of which are given some ideas about making a drawing by correlationline projection are analysed and the actual drawing process is illustrated.

用解析法探讨了两轴线相交的回转面的相贯线投影的形状，分析了双曲线的一些相关特性，在此基础上给出了相贯线投影作图的新思路；利用实例说明了具体的作图过程。

Our factory is a specialized enterprise which major in production stainless steel, stainless steel wire,Stainless steel round steel, Stainless steel flat steel, Stainless steel cold-drawing light bar, Stainless steel angle iron, Stainless steel square iron , Stainless steel hexagon bar;,Stainless steel cold-drawing section, Stainless steel wire, Stainless steel chain link, Stainless steel mesh belt, Stainless steel chain wheel, Stainless steel pressing part, rustless iron and special steel products .

本厂是专业生产不锈钢，不锈钢丝；不锈钢圆钢；不锈钢扁钢；不锈钢冷拉光元；不锈钢角钢；不锈钢方钢；不锈钢六角棒；不锈钢冷拉型钢；不锈钢丝绳；不锈钢链条；不锈钢网带；不锈钢链轮；不锈钢冲压件，不锈铁与特殊钢材的专业性企业。

Purpose: To explore further improvement of method in treating anus fistula, by observing curative effect of incision thread-drawing adding hemostasis by compression and sutura in anus fistula, and comparing the cure effect of treatment group with control group, so that the cure effect of incision thread-drawing adding hemostasis by compression and satura was verified and was affirmed.

目的：通过观察切开或切开挂线加缝压止血法治疗肛瘘的疗效，并将切开或切开挂线加缝压止血法与切开或切开挂线法的疗效进行对照比较，对临床治疗肛瘘的方法进一步改进进行初步的探索，验证从而肯定切开或切开挂线加缝压止血法在肛瘘治疗中的作用。

This design content is determined the superposable die former and the structural style as well as the technology capability, draw up the mold assembly drawing and the non-standard letter detail drawing.

本设计的内容是确定复合模内型和结构形式以及工艺性，绘制模具总图和非标准件零件图。

The superposable die has used the true thing form in the structure, calculated fell the material, the drawing and the counter- drawing effective range size.

复合模在结构上采用了正装的形式，计算出了落料、正拉深和反拉深工作部分的尺寸。

The superposable die has used the true thing form in the structure, calculated fell the material, the drawing and the counter- drawing effective rang

复合模在结构上采用了正装的形式，计算出了落料、正拉深和反拉深工作部分的尺寸。

I can not make it blossom and suits me

我不能让树为我开花

When temperatures are above approximately 80 °C discolouration of the raceways or rolling elements is a frequent feature.

当温度高于 80 °C 左右时，滚道或滚动元件褪色是很常见的特征。