查询词典 double ratio

In this paper, through a series of experiments, two series of quaternary-ammounium Gemini surfactants were synthesized, namely the pair alkylene double quaternary ammonium salt surfactant m-s-m·2Br and the pair the alkylene double quaternary ammonium salt surfactant -s-·2Br. We has carried on the attribute with the infrared spectrum to its structure, and to affected the factor which the synthesis pair the alkylene double quaternary ammonium salt surfactant responded to carry on the discussion. We has discovered the synthesis pair the ethylene double quaternary ammonium salt surfactant m-2-m·2Br optimum condition: The bromo alkane and a tetramethyl ethylene diamine mole of ratio is 3.0: 1.0, makes the solvent by the ethyl alcohol, 80℃ under responds for 48 hours in the backflow temperature; Synthesis pair alkylene double quaternary ammonium salt surfactant 12-S-12 ·2Br optimum condition: 12 tertiary amine and 1, 3- propylene dibromide (1, 4- two bromines butane) a mole of ratio is 2.2: 1.0, makes the solvent by the ethyl alcohol, responds for 48 hours in the constant temperature 80 ℃ under backflow.

本文通过一系列的实验，合成了两个系列的Gemini型表面活性剂，即双烷撑双季铵盐表面活性剂m-s-m·2Br和双烷撑双季铵盐表面活性剂-s-·2Br，用红外光谱对其结构进行了表征，并且对影响合成双烷撑双季铵盐表面活性剂反应的因素进行了讨论，找出了合成双乙撑双季铵盐表面活性剂m-2-m·2Br的最佳条件：溴代烷与四甲基乙二胺的摩尔比为3.0：1.0，以乙醇作溶剂，在回流温度80℃下反应48小时；合成双烷撑双季铵盐表面活性剂12-s-12·2Br的最佳条件：十二叔胺与1，3-二溴丙烷(1，4-二溴丁烷)摩尔比为2.2：1.0，以乙醇作溶剂，在恒温80℃下回流反应48小时。

To satisfy the specified needs in application,irregular speed-change can usually be adopted such as much-speed motor ,mixed double ratio and so on.

在实际使用中，为了满足一些特定的要求，往往采用非常规变速，如多速电机、混合公比或者背轮机构等。

At the same time, the Yu Liang of president of 10 thousand divisions that attends the meeting also expresses: Now is not all cities, all market appear the phenomenon of get warm again after a cold spell, the house that is low total prices, low monovalent and rigid demand only at present is more active into double ratio.

同时，出席会议的万科总裁郁亮也表示："现在并不是所有城市、所有市场都出现回暖的现象，目前只是低总价、低单价刚性需求的房子成交比较活跃。"

We mainly produce auto rear axle and its spindle now and we have developed other reserve products such as double ratio feeling reel and stainless parts of electricity transmission.

我公司成立于2004年，主营业务为汽车零配件、五金件、橡塑件等，目前主要生产汽车后桥及其芯轴，公司同时开发了变速渔轮、不锈钢电力金具等后背储备产品。

The main results of the study are obtained as follows:1 In order to analyze and study the physical and mechanical characteristics of Lianyungang marine soft clay deeply, large numbers of basic mechanical characteristics tests and tri-axial shear tests are completed.2 In order to investigate the loaded and failure characteristics of the cement-soil, the cement-soils for the different ratio and different cure time are studied in the laboratory, and their unconfined compression tests and tri-axial shear tests are performed.3 Based on the solution of one-dimension consolidation, the one-dimension consolidation of the double-layered foundation is solved for two-grade loading in virtue of transcendental equation; Simultaneously, the one-dimension consolidation of the double-layered foundation is solved by means of Laplace transform for two-grade loading, and Stehfest numerical transform is applied in Laplace's inverse transformation; Furthermore, according to the practical foundation shapes, the consolidation models of the soil between piles and the substratum are built and solved respectively.4 The effect of each parameters on the consolidation of the double-layered foundation is discussed, and the solution of load transfer method for double-layered foundation is applied in A1-A4 section of Lian-Xu expressway. The results of calculating settlement of the double-layered consolidation theory are basic agreement with the measuring settlement results.

取得了以下几方面的研究成果：1针对连云港海相软土进行一维固结和三轴剪切试验，深入分析连云港海相软土的物理力学特性。2模拟水泥土搅拌桩施工，在室内制备不同配比、不同龄期的水泥土试样，并进行无侧限抗压试验和三轴剪切试验，揭示水泥土的受力特性及破坏特性。3运用超越方程，以双层地基一维固结解析解为基础，推导出二级加荷条件下双层地基的固结解析解；同时，通过荷载传递法并借助Laplace变换对双层地基的固结问题进行了数值求解；此外，根据实际的地基结构，建立了桩间土和下卧层的固结模型并分别进行求解分析。4分析探讨了双层地基中各参数对双层地基固结的影响程度，并运用荷载传递法的解答计算了连-徐高速公路A1-A4标水泥土搅拌桩处理段的六个断面，计算结果与实测数据有较好的一致性。

The UV and IR spectroscopic studies of the monomer films showed that the photoreaction ratio of monomer (about 50%) was higher than the corresponding photosensitive polymer (about 10%, PVCi). The polarized IR spectra proved that obvious anisotropic absorption was displayed in the irradiated photosensitive film. With polarizing microscopy method, we found that these kinds of photoalignment films exhibited good alignment ability, and the stability of the photoalignment film could reach about 100℃. 2 A photosensitive self-assembled monolayer was fabricated that contained photo-cycloadditable groups, such as, coumarin and cinnamate. The reaction process were detected by contact angle method because the IR absorption of monolayer was very weak. The photosensitive self-assembled monolayer promote uniform alignment of nematic liquid crystals by LPUV, and it thermal stability could reach about 130℃. 3 A cationic bolaform amphiphiles was synthesized that had two photosensitive double bonds, and can be polymerized by ultraviolet. A layer-by-layer self-assembled deposition film was prepared in aqueous solution by using this material and poly (sodium 4-styrenesulfonate). The UV-Vis. spectra proved that the multilayers film was uniform and layer-by-layer. When LPUV irradiated the film, the photopolymerizable double bond underwent [2+2] cycloaddition, and the production of the reaction distributed along the polarized direction of incident LPUV. Polarized UV-Vis. spectra indicated that the irradiated self-assembled multiplayer film was anisotropic, and the dichromic ration is about 0.09, it is higher than the spin-coating method of photosensitive polymer or monomer. We used this anisotropic film as alignment layer of nematic liquid crystals, and obtained a uniform and stability alignment result, the static contrast ratio is about 100, which is very close to application of liquid crystal device. This thesis is an instance that the photochemical material was used in the physics region of liquid crystals, the route that was from photosensitive monomer, self-assembled monolayer film to self-assembled multiplayer film was undergone, by this logical research method photoailgnment of liquid crystal was extended and consummated.

围绕上述思路开展了如下工作：1合成了三种可进行光二聚反应的光敏小分子单体，LPUV 辐照制作了光控取向膜；用紫外-可见光谱法和红外光谱法分析了薄膜中的光化学反应，发现小分子的光反应程度可达到50%以上，至少比光敏高分子高出5倍；薄膜的偏振红外光谱证实，经过LPUV 辐照后薄膜出现了明显的各向异性；将小分子光控取向膜制成液晶器件，在偏光显微镜下观察看到均匀一致的液晶取向；并且热稳定性达到100℃左右，接近实用化要求。2制备了含肉桂酸、香豆素基团的自组装单层膜；采用接触角的方法监测自组装反应的动力学过程；紫外-可见光谱证实了自组装单层膜在石英基板表面形成；自组装单层膜经LPUV 辐照后能诱导液晶均匀取向，而且热稳定性可达130℃，热稳定性进一步提高。3合成了含有光敏双键的双季铵盐，在水溶液状态下将它和聚乙烯基苯磺酸钠沉积生成layer-by-layer 自组装多层膜，紫外-可见光谱证实这是一个逐层均匀的沉积；在LPUV 照射下，自组装膜中的光敏双键按照偏振方向发生[2+2]环加成反应，形成取向膜，用二向色性值评价的分子取向度高于高分子及小分子光控取向膜的水平；实验证明用自组装多层膜制成的液晶器件亮暗态均匀，静态对比度约为100，达到实用化器件的水平。

The fiber length has only little influence on the basic density within the growth rings, and significant correlation at 0.01 levels was found between the basic density and the fiber length among the different rings. Only slight negative correlation was found between the basic density and the fiber width within the growth rings, but significant positive correlation at 0.01 levels was indicated between the basic density and the fiber width among the growth rings, contrary to that of fiber length. It was demonstrated that significant positive correlations at 0.01 levels between the basic density and fiber double wall thickness, fiber length to width ratio and double wall thickness to diameter ratio, significant negative correlations at 0.01 levels between the basic density and fiber diameter and diameter to width ratio, only slight negative correlation between the basic density and fiber width both in the same growth rings and among the different growth rings. No significant correlation was found between the basic density and the vessel morphological features, nor was the tissue proportion in the same growth rings. But among the different rings, it was found there was significant positive correlation at 0.01 levels between the basic density and the fiber proportion among the different rings, and significant negative correlation at 0.01 levels between the basic density and vessel-elements proportion and ray proportion, only slight negative correlation between the basic density and the parenchym proportion. Significant or no significant negative correlation was found between the basic density and the microfibril angle in the same growth rings, but significant negative correlation was found between the basic density and the microfibril angle among the different growth rings.

生长轮内纤维长度对基本密度的影响不大，而在不同生长轮间纤维长度与基本密度达极显著正相关，纤维宽度与此相反，同一生长轮内纤维宽度与基本密度极显著负相关，不同生长轮间只有微弱负相关；基本密度与纤维双壁厚、长宽比、壁腔比在生长轮内和生长轮间均呈极显著正相关，而与胞腔直径、腔径比均呈极显著负相关，仅与纤维宽度呈微弱的负相关；导管形态对基本密度的影响不显著；同一生长轮内组织比量对基本密度的影响也不显著，但不同生长轮间基本密度与纤维比量呈极显著正相关，与导管比量和木射线比量呈极显著负相关，与轴向薄壁细胞比量仅呈不显著负相关；生长轮内基本密度与微纤丝角呈显著或不显著负相关，但在生长轮间这种负相关达到极显著水平。

We mainly produce auto rear axle and its spindle now and we have developed other reserve products such as double ratio feeling reel and stainless parts of electricity transmission.

商铺介绍：我公司成立于2004年，主营业务为汽车零配件、五金件、橡塑件等，目前主要生产汽车后桥及其芯轴，公司同时开发了变速渔轮、不锈钢电力金具等后背储备产品。

We mainly produce auto rear axle and its spindle now and we have developed other reserve products such as double ratio feeling reel and stainless parts of electricity transmission.

企业介绍：我公司成立于2004年，主营业务为汽车零配件、五金件、橡塑件等，目前主要生产汽车后桥及其芯轴，公司同时开发了变速渔轮、不锈钢电力金具等后背储备产品。

At the same time, the finite staff element method is used to analyze the influence of beam rigidity; and the two new methods proposed are used to analyze the influence of connect way between piles and beam; and the conclusion is obtained that the rigidity ratio between beam and piles being 0.48 is appropriate; the continuative increase of the rigidity ratio is not significant; the worst condition is that connecting way between piles and beam is hinged; the best condition is that connecting way between piles and beam is rigid. Whether is single-row pile or are double-row piles, when the front of single-row pile or the front of the front-row pile(in the double-row piles) needed excavation, it is supposed to that ought to be carefulness to excavate, because it is that the engineering cost increased greatly.

同时，用有限杆单元法，对双排桩的连梁刚度和用文中提出的方法以桩梁连接方式进行了试验和理论分析得出如下结论：在满足不相互影响排桩间距的情况下，桩顶连梁与桩的刚度比不小于0.48是合适的，此时再增加连梁刚度无意义；桩梁连接为铰结时双排桩受力变形性质最差，刚结时受力变形性质最好；不论是单排桩还是双排桩，桩前和前排桩桩前土体需要开挖时应慎重，因为这种开挖对支护结构影响很大，造价增加很多；双排桩省钱，而且抵抗变形的能力强，值得在工程中研究和广泛应用

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。