查询词典 distribution parameter

Research results show that under AC voltage the voltage distribution of Y-type insulator strings is extremely non-uniform and the voltage distribution curve of Y-type insulator string is similar to that of I-Type suspension insulator string; under DC voltage the voltage distribution of Y-type insulator string is also extremely non-uniform, the voltage undertaken by the insulators at the conductor side of Y-type insulator string is higher than that undertaken by other insulators of the same string, and as a whole the voltage distribution trend is that the voltage undertaken by the insulators at both ends of the Y-type insulator string is higher than the voltage undertaken by the insulators at the middle of the same insulator string.

研究结果表明：在交流电压下，Y型绝缘子串的电压分布极不均匀，其电压分布曲线和交流悬垂I串类似；在直流电压下，Y型绝缘子串的电压分布极不均匀，绝缘子串导线侧绝缘子分担电压高于其它绝缘子，总体上呈现导线侧和杆塔侧两端高、中间低的分布趋势。

The following conclusions are drawn. 1 The orbit parameters that have relatively greater influence on the number and latitudinal distribution of annual occultation events are orbit inclination, orbit height, Right Ascension of Ascending Node and Argument of Perigee in turn. All four parameters have little impact on the longitudinal distribution of annual occultation events. 2 The orbit inclination of Transmitting Satellite and Receiving Satellite impacts both LEO－LEO occultation events number and their latitudinal distribution most. The number of occultation events reaches the maximum as the sum of the two inclination angles nears 180 degrees. The one that far away from 90 degrees of the two inclination angles determines the latitude range of the occultation events. 3 LEO－LEO occultation events number reaches a maximum when the heights of TS and RS are the same, and it reaches the maximum when the heights of TS and RS are 600 km . 4 The RAAN of TS and RS has a great influence on the LEO－LEO occultation number, but has little influence on occultation distribution.

结果指出：1对一年掩星事件数量及其纬度分布影响大的轨道参数依次是轨道倾角、轨道高度、升交点赤经和近地点角距；而这些参数对一年掩星事件的经度分布影响都不大；2发射卫星和接收卫星倾角之间的相互关系对掩星事件数量和纬度分布影响最大，两卫星倾角接近互补时掩星事件最多，两颗LEO卫星中与90°相差较大的倾角决定了LEO－LEO掩星事件的纬度分布范围；3发射卫星和接收卫星处于同一轨道高度时，LEO－LEO掩星事件数取得极大值，发射卫星和接收卫星都采用600 km的轨道高度，一年LEO－LEO掩星事件数最多；4 发射卫星和接收卫星升交点赤经的相互关系对LEO－LEO掩星事件数量影响很大，发射卫星和接收卫星升交点赤经之差为120°或240°时掩星事件数量最多，RAAN对掩星事件纬度和经度分布影响不大；5近地点角距对掩星事件数量和分布影响都不大。

The stress distribution of the semi-circular breakwaters with holes by different quantitative ice value to water level, especially the stress distribution of holes is analyzed. The effect of the stress distribution to the holes and the wall thickness are discussed. At last, the result is compared to the stress distribution by wave

应用ANSYS程序计算了不同水位不同量级冰力作用下开孔半圆型防波堤的应力分布，尤其分析了孔洞周围的应力分布；并且讨论了开孔和壁厚对于应力分布的影响；最后将分析结果与波浪力作用下的应力分布进行了比较。

But when a rectangular continuous data set appears to have a longer tailed than normal distribution or it contains some values that are influential on statistical inference with normal distribution, the multivariate t distribution becomes useful for multiple imputations as an alternative to the multivariate normal distribution.

在多重插补法的基础上，当一个矩形连续数据集看起来有一个比正态分布还长的尾巴，或者是它包含了一些对正态分布的统计推断有影响的数据，多元t分布作为多元正态分布的替代分布，对于多重插补来说变的很有用了。

Thirdly, by con-utilaziont of many methods such as exploitation and geology, dynamic producing process monitoring, water invasion behavior, core analyis and numerical simulation, 10 kinds of reservoir scale remaining oil distribution pattern in the steam huff and puff super heavy crude oil reservoir was put forward. Also, remainling oil distribution in the sand bed scale and sublayer scale were pointed out.Fourthly, Microcosmic displacement experiment was conducted for hot water driving in 100℃and 120℃. and steam drive at 170℃condition. Microcosmic remaining oil distribution characteristics were summarized. Remaining oil microcosmic distribution by steam drive at 170℃is different from that at 100℃, 120℃hot water driving. After the steam drive, there are three types of remaining oil distribute regular pattern, whic is impacted by many affecting factors like pore configuration, wettability and interfacial tension.

分析了砂层组规模和小层规模的纵向和平面剩余油分布规律。4、通过微观驱替实验，研究了100℃和120℃的热水驱及170℃蒸汽驱条件下剩余油的微观分布形态。170℃条件下剩余油微观分布形态同时受孔隙结构、润湿性及界面张力多种因素的影响，主要有三种形式：在油、汽、水三相共存的孔隙中，剩余油分布于汽、水之间，为薄膜状和弯月状；在只有油、汽两相共存的孔隙中，大孔道中主要是蒸汽，剩余油在细小的孔喉和孔隙角隅处以段塞或不规则状态存在；由于高温水蒸汽对原油具有萃取作用，剩余油以一种细小的珠滴状存在于孔隙表面。

So the research on non-parameter reliability estimate is changed to the estimating of parameter R in Binomial distribution.

在多层Bayes方法中，提出了R的多层先验分布的构造方法——增函数法，并给出了在无失效数据问题中的应用。

This paper presents an IFMC CAD model that consits of a geometry model and a material model, in which the geometry space acts as a base space and the material space acts as a bundle space. In this CAD model, the geometry model is based on the non-manifold model. In addition, a half-face data sturucture, which is derived from the half-edge data structure with the non-manifold feature of IFMC taken into account, is adopted to represent the geometry and topology information of the component. For the material model of IFMC, this paper focuses on the FGM component representation firstly and present a simplex-subdivision based CAD data exchange format, in which the material information is represented as a (n-1) simplex and material distributing feature is represented by the interpolation on the simplex-subdivision. Based on those, a part-building orientation optimization algorithm and an adaptive slicing algorithm for FGM component are presented in the paper. For the IFMC material model, the IFMC material information representation is divided into a meso-scale and a macro-scale representation. In the meso-scale, a concept named parameterized periodic functional meso-structure is presented as a unique form to represent the FGM (the homogeneous materials are regarded as a special FGM), the composite and the functional meso-structure material. The model of PMS is a three-tuple that contains the space state informatation, the material parameter and the material meso-scale distribution feature. The macro-scale material information representation is similar to the FGM components by interpolation of the control parameter of the periodical functional meso-structure based on the simplex-subdivision. Through an example of manufacturing-oriented IFMC CAD data processing, it is proved that the IFMC CAD model and the material information representation and process method proposed in this paper can provide a reliable data support for IFMC digital concurrent design and manufacturing.

本文将理想材料零件CAD模型建立在以几何空间为底空间、以材料空间为丛空间的结构上，使用非流形几何模型作为理想材料零件几何拓扑模型的基础，并在半边数据结构基础上，针对理想材料零件的非流形特征局限内部边界上的特点，给出了一个半面数据结构来表述零件的几何拓扑信息；对于理想材料零件的材料模型，本文先从功能梯度材料零件的信息表述与CAD数据交换和处理入手，将材料信息表述为（n-1）维单纯形，然后通过对三维几何区域的单纯剖分，以插值的方式表述零件材料分布特征；在此基础上，根据功能梯度材料零件分层制造中对CAD数据处理的要求，给出了综合考虑零件几何特征与材料特征的生长方向优化算法和自适应切片算法；而对于文中所定义的理想材料零件，本文将其材料信息表述分解到细观和宏观两个尺度进行，首先给出了细观尺度上参数化的周期性功能细结构概念，以此来统一表述功能梯度材料（单质材料作为特殊的功能梯度材料看待）、复合材料和功能细结构材料；把周期性功能细结构模型化为一个包含空间状态信息、材料构成参数和材料细观分布特征参数的三元组，以表达零件的细观材料特征；对于零件宏观的材料变化特征，则同样在几何区域单纯剖分的基础上，通过对细观尺度上周期性功能细结构控制参数的插值来完成；通过理想材料零件CAD数据处理的算例，验证了本文中理想材料零件CAD模型及材料信息表述与处理方法完全可以为理想材料零件的数字化制造提供可靠的数据支持。

This paper presents an IFMC CAD model that consits of a geometry model and a material model, in which the geometry space acts as a base space and the material space acts as a bundle space. In this CAD model, the geometry model is based on the non-manifold model. In addition, a half-face data sturucture, which is derived from the half-edge data structure with the non-manifold feature of IFMC taken into account, is adopted to represent the geometry and topology information of the component.For the material model of IFMC, this paper focuses on the FGM component representation firstly and present a simplex-subdivision based CAD data exchange format, in which the material information is represented as a (n-1) simplex and material .distributing feature is represented by the interpolation on the simplex-subdivision. Based on those, a part-building orientation optimization algorithm and an adaptive slicing algorithm for FGM component are presented in the paper.For the IFMC material model, the IFMC material information representation is divided into a meso-scale and a macro-scale representation. In the meso-scale, a concept named parameterized periodic functional meso-structure is presented as a unique form to represent the FGM (the homogeneous materials are regarded as a special FGM), the composite and the functional meso-structure material. The model of PMS is a three-tuple that contains the space stateinformatation, the material parameter and the material meso-scale distribution feature. The macro-scale material information representation is similar to the FGM components by interpolation of the control parameter of the periodical functional meso-structure based on the simplex-subdivision.Through an example of manufacturing-oriented IFMC CAD data processing, it is proved that the IFMC CAD model and the material information representation and process method proposed in this paper can provide a reliable data support for IFMC digital concurrent design and manufacturing.

本文将理想材料零件CAD模型建立在以几何空间为底空间、以材料空间为丛空间的结构上，使用非流形几何模型作为理想材料零件几何拓扑模型的基础，并在半边数据结构基础上，针对理想材料零件的非流形特征局限内部边界上的特点，给出了一个半面数据结构来表述零件的几何拓扑信息；对于理想材料零件的材料模型，本文先从功能梯度材料零件的信息表述与CAD数据交换和处理入手，将材料信息表述为(n-1)维单纯形，然后通过对三维几何区域的单纯剖分，以插值的方式表述零件材料分布特征；在此基础上，根据功能梯度材料零件分层制造中对CAD数据处理的要求，给出了综合考虑零件几何特征与材料特征的生长方向优化算法和自适应切片算法；而对于文中所定义的理想材料零件，本文将其材料信息表述分解到细观和宏观两个尺度进行，首先给出了细观尺度上参数化的周期性功能细结构概念，以此来统一表述功能梯度材料(单质材料作为特殊的功能梯度材料看待)、复合材料和功能细结构材料；把周期性功能细结构模型化为一个包含空间状态信息、材料构成参数和材料细观分布特征参数的三元组，以表达零件的细观材料特征；对于零件宏观的材料变化特征，则同样在几何区域单纯剖分的基础上，通过对细观尺度上周期性功能细结构控制参数的插值来完成；通过理想材料零件CAD数据处理的算例，验证了本文中理想材料零件CAD模型及材料信息表述与处理方法完全可以为理想材料零件的数字化制造提供可靠的数据支持。

The data analysis shows that: 1 different texture parameters have a clear scattered distribution, 2 the main direction of texture is the direction represented by the maximum parameter of Gauss-MRF parameters, and 3 for those samples basing the same main direction, the finer the texture is, the greater the corresponding parameter is, and the smaller the other parameters are; and the higher the order of Gauss-MRF is, the more clearly the texture is described.

数据分析表明，各不同纹理特征参数之间具有明显的分布性；Gauss-MRF参数值最大的参数所表示的纹理集聚为向为纹理的主方向；对于纹理主方向相同的样本，纹理越细致，其相应参数越大，而其他参数越小；Gauss-MRF阶数越高，纹理描述越细致：在2阶Gauss-MRF模型情况下，弦切纹理的B1参数大于径切纹理的B1；弦切纹理的B2、B3、B4分别小于径切纹理的B2、B3、B4。

Nozzle distribution design, picking the 3D placement points of nozzle on solid directly and adjusting position parameter, direction parameter freely, it will display the axis direction of nozzle momentarily.

布置喷嘴设计，直接在三维实体上点选放置点，随意调整位置、方向参数，实时显示喷嘴轴线方向。

Salt is good, but if the salt becomes flat and tasteless, with what do you season it?

14：33 盐本是好的，盐若失了味，可用什么叫它再咸呢？

He reiterated that the PLA is an army of the people under the leadership of the Communist Party of China.

他重申，人民解放军是在中国共产党领导下的人民军队。