查询词典 distortion angle

The binder orientation angle and bending distortion of the specimen are small.

经预拉伸后的试样，接结经的取向角小，弯曲变形小，材料表现出低伸、高强、高模量的特点。

It is found that the main source of fillet weld's angle distortion is the inherent shear strain component ε but not the transverse inherent normal component.

结果发现：角焊缝产生角变形的主要根源是固有剪切应变，而不是传统思维认为的横向固有正应变，且角变形的大小与固有剪切应变的分布形式密切相关。

The Electronic Map is scanned into computer. Since the source of the images is different, and there is angle, geometry distortion and even different resolving rate between the images, these factors add the difficulty of image match.

由于电子地图来源于纸质地图的扫描，它与遥感影像图生成的机理不一致，又存在着一定的角度失真和几何形变问题，甚至它们的分辨率也不一样，从而增加了配准的难度。

The degree of twist distortion increases with pretilt angle.

同一种液晶分子在取向层的预倾角不同，在力场作用下扭曲变形的程度亦不同，预倾角较大可获得较大的扭曲角；对于不同的向列液晶，弹性常数较小的液晶可在较短的时间产生较大的扭曲变形

This paper expounds the relationship between the property right and the accounting information,analyzes on the reasons of information distortion from the angle of the property right theory,and advances some countermeasures for improving the accounting information quality through making clear the property right,constructing the motivation mechanism and restraint mechanism,and improving the supervision function,etc.

论述了产权与会计信息的关系，从产权理论角度分析了会计信息失真的原因，提出了明晰产权、建立激励和约束机制、改善监督职能等提高会计信息质量的对策。

Chapter 4: Influence of the angle distortion induced from rhombohedral La_(0.7)Sr_(0.3)MnO_3 grown on the cubic substrates on the structure and transport properties of CMR thin films is carefully studied.

第四章研究菱形结构的La_(0.7)Sr_(0.3)MnO_3生长在立方衬底上引起的角度畸变对薄膜的微结构和电磁性质的影响。

Axial-flow compressor ; experimental investigation ; inlet pressure distortion ; absolute flow angle

轴流压气机；试验研究；压力畸变；绝对流动角

In the end, we sum up the current research in the manganite thin films (such as the influence of oxygen stoichiometry, lattice-misfit strain and angle distortion induced strain on the thickness effects) and some existent issues.

最后讨论了锰氧化物外延薄膜的制备方法，及影响锰氧化物薄膜结构和电磁性质的相关因素(如氧含量，晶格失配应变，薄膜厚度，角度畸变及热膨胀系数等)以及期待解决的问题。

Taking a welded T-joint as computing example,the forming mechanism of fillet weld's angle distortion was studied by combining thermal elastic plastic analysis with mapping strain component method.

以T形焊接接头为算例，结合热弹塑性有限元法和映射应变分量法，研究了角焊缝角变形的产生机制。

It is clearly that only two geometrical parameters i.e. maximal misalignment angle and distortion width need to be determined experimentally.The engineering constants around the stitch hole in the composite laminate are analyzed using the FDM.

采用纤维弯曲模型分析了缝纫复合材料单层在缝纫孔附近的最大纤维偏转角、缝纫影响区以及缝纫复合材料单层及层合板工程常数的变化，发现工程常数具有很明显的区域性，能够看出各层中树脂富集区的痕迹。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。