查询词典 discharge in a jet

In order to improve the efficiency of the jet pump,the measures can be taken includes:the use of pulse-jet or multi-shares Jet.

为了提高射流泵的效率，可以采取的措施有：采用脉冲射流或多股射流。

The results show that the new jet area formed by lateral jet minishes the coverage area of vortex at the bottom, and it plays an active role in cleaning the bottom; driven by the lateral jet, shear stress and pressure difference increase on cutting surface, which helps inhibit the growth of balling and cooling blade to improve bit performance.

研究结果表明：侧向射流形成新的射流区，减小了井底漩涡的覆盖面积，对井底清岩能起到积极作用；在侧向射流带动下，刀翼切削面的剪切力、压力梯度增大，利于抑制泥包的成长和冷却刀翼，提高钻头性能。

Ink-jet Figure 2-22 Ink-jet printer An ink-jet printer is a type of nonimpact printer that forms characters and graphical by spraying tiny drops of liquid ink onto piece of paper.

喷墨打印机是一种非击打式打印机，通过向纸上喷洒微小的液体油墨而形成字符和图形。

The gel dynamics experiments showed that the gel formation law was similar with the other polymer systems, which wasrelated with dense surface under the soft coagulating condition and the thickening gel; the square of gel thickness was linear with coagulation time. The qualitative analysis of the surface puckers of fibers spun from wet spinning and dry-jet wet spinning was made. The positions where the die swell appeared were not the same and the die swell appeared at the air gap where the fiber would markedly been elongated and vary little in the coagulant, thus the surface of fiber spun from dry-jet wet spinning was more smooth. The radial component concentration gradient was responsible for the radial structure of PAN fiber spun from dry-jet wet spinning. The thicker surface with microvoid structure of

对湿纺和干湿纺进行比较表层沟槽的产生进行定性分析，原因在于孔口胀大区域出现在不同位置，在干湿纺中，溶液的孔口胀大出现在空气层，并在该区完成大部分形变，进入凝固浴后形变很小，纤维表面较为光滑；干湿纺PAN纤维径向结构存在差异，这与丝条内组分由于双扩散进行导致径向上存在浓度差异直接相关；凝固强度较大的体系，可以获得厚度较大且孔结构尺寸较小的皮层；含较少缠结的PAN原液在纤维成形后截面很圆整，但原液缠结浓度增大时成形后圆整度下降；PAN纤维成形是一个远离平衡的过程，凝固作用缓和的体系可以使成形过程靠近平衡，可获得更大尺寸的孔洞结构；原液中少量的非溶剂添加剂显著改变纤维径向结构，可获得孔洞尺寸更小和更为均一的径向结构，这与径向浓度差异的减小、分相时间的集中相关；PAN原液的成形纤维表面依赖于凝固强度；由AFM对相近凝固条件下成形的PAN膜进下

The results show that: Near the slot exit, three synthetic jets couple to one jet and move downstream. Two synthetic jets on both sides are limited and rolled by the middle synthetic jet until they merge together into one centrosymmetric synthetic jet.

研究结果表明：三股自耦合射流都在出口附近耦合成一股射流向下游运动，两侧的射流受到中间一股射流的卷吸融合在一起，融合后仍然是一股沿中心线对称的自耦合射流。

The deflective mechanism of the oscillating water jet is analyzed and the effects of jet deflection on the self oscillating water jet are investigated.

分析了自激振荡射流的偏转特性，研究了偏转特性对射流振荡脉冲压力、射流切割性能等方面的影响。

According to the actual parameters of coal mining face, the models of jet blower and air compressor are made out. Then locate the jet blower on mining face and air screen is produced by the jet blower to prevent the gob areas gas effusing to the top even angle.

然后在工作面具体安放射流风机，通过射流风机产生空气幕进行均压、阻断采空区瓦斯向上隅角涌出。

A hotwire anemometer was used to measure the jet velocity at the exit of the precessing jet nozzle and the power spectrum density was obtained afterwards in order to analyze the precessing feature of the jet. It is shown that an obvious precession motion is generated in a nozzle even with a large expansion ratio E=10 and a small length-to-diameter ratio LD=2. The precessing frequency is mainly dependent on the nozzle diameter and the intake flow rate, increasing with the enhancement of the flow rate and with the reduction of nozzle diameter.

采用热线风速仪测量旋进喷嘴出口射流的速度，并对该射流进行功率谱分析以研究其旋进特性，结果表明，实验所用的膨胀比E=10、长径比L/D=2的喷嘴同样能产生明显的旋进射流，旋进频率主要取决于喷嘴的尺寸和射流的流速，并随流速的增大和喷嘴直径的减小而增大。

Integrated analysis of 7 times heavy rain in Yunnan from July 19 to August 2 based on actual observation weather datum and satellite cloud atlas and Doppler radar image. The results show that: high-low southwest jet stream is important effect system. The maintenance of southwest jet stream provides water vapor, momentum, fast transfer of unstable energy for the lasting heavy rain. The further configuration of plateau shear line and southwest jet stream is necessarily condition about 7 times heavy rain. The lasting heavy rain appeared on big value region of 500hPa vapour flux and vapour flux divergence. The shear cloud band and subtropical high cloud band crossed and confluenced in Yunnan on the satellite cloud atlas. The maintenance and intensification of shear cloud hand and periphery cloud band of subtropical high correspond quite well to heavy rain falling region and cloud band distribution.

应用实测气象资料，结合卫星云图与多普勒雷达图像分析，对2007年7月19日到8月2日云南少有的7次强降水过程进行综合分析，结果表明：高低空的西南急流是重要的影响系统，西南急流的维持为持续性强降水过程提供了水汽、动量和不稳定能量的快速传递，高原切变线与西南急流的有利配置，是7次持续性强降水过程必不可少的条件；持续性强降水出现在500hPa水汽通量大值区和水汽通量散度辐合区；卫星云图上切变云带和副高外围云带在云南汇合，切变云带和副高外围云带维持、加强的过程与强降水落区的时空分布对应较好。

In comparison with bugle shaped nozzle, bifurcated nozzle downward jet angle 45°, cow-nose nozzle and three-hole nozzle, in all, the last two are better than the former and bifurcated nozzle downward jet angle 45 is better than bugle shaped nozzle; Cow-nose nozzle is helpful for guaranteeing the product's quality, in order to protect jet flow from eroding the strand at narrow face, gain uniform temperature distribution at cross section and decrease heat flux, adding the block's width to 100 mm. Three-hole nozzle is advantageous to increase flux and casting speed, but should avoid weak shell thickness in the center broad. In the real production, setting the SEN's immersed depth or plugging the hole at the bottom can adjust the flow and temperature distribution in the mold.

对比喇叭形水口，双侧孔水口(45°)，牛鼻子水口和三孔水口，总的说来后两者优于前两者；而双侧孔水口(45°)又优于喇叭形水口；牛鼻子水口和三孔水口比较各有特点，前者对保证铸坯质量有利，为防止流股对窄面的冲击，增加挡块宽度到100 mm，可使结晶器横截面上温度分布更加均匀，降低窄面热负荷；后者对增加流量，提高拉速非常有利，但要防止中孔射流过强导致铸坯中心坯壳变薄，在实际生产中可通过控制水口浸入深度或塞住浸入式水口的底孔来调节结晶器中的流动与温度分布状态。

The use of the web to spread fears that flicking the switch on the LHC could create a Black Hole that could swallow up the Earth particularly concerned him, he said.

他说，使用互联网散布恐慌说启动LHC会生成一个可能吞噬地球的黑洞的做法让他感到忧虑。

Not a single word have I written down.

我一个字也没有写下来。