查询词典 dilatometric

Based on analyzing the dilatometric curves, metallographic structures of test samples of these simulation procedures, four factors which have influences on the tendency of the appearance of the cold cracks in HAZ have been studied, these factors are preheating, slow cooling, expanding the cooling time (t8/5 and t8/3), and heat preservation.

通过对这些模拟过程的热膨胀曲线、试样金相组织等的分析，研究了焊前预热、焊后缓冷、延长冷却时间t8/5与t8/3、焊后保温这四种因素对焊接热影响区冷裂纹产生倾向的影响。

By the method of dilatometric change,combining with microscopic test and hardness measurement,different expanding curves of continuous cooling transformation were measured at different cooling rate,and CCT diagram was obtained by using DIL805A thermal expansion fast phase transition instrument.

利用膨胀法，结合金相法和硬度法，在DIL805A热膨胀快速相变仪上测定了该钢在不同冷速下连续冷却时的热膨胀曲线，获得了该钢的连续冷却转变曲线；研究了该钢连续冷却过程中奥氏体转变过程与组织变化。

The effect of Stress applied at certain temperature on low temperature phase transformation of T91 was studied with Baehr DIL805A/D high-resolution differential dilatometer. According to the results of dilatometric measurement and microstructure observation, kinetics of phase transformation was obtained.

采用Baehr DIL805A/D高精度差分膨胀仪测量线膨胀行为与微观组织分析获取了T91铁素体耐热钢低温相变过程动力学信息，研究不同温度（760、650和440℃）下施加不同压应力（100、150和200 MPa）对低温相变过程的影响。

By dilatometric change referencing microscopic test and hardness measurement, the critical point at Ac1, Ac3 and Ms of 27CrMo27S steel was determined in Gleeble-3800 thermal mechanical simulator, By measuring the different expanding curves of CCT in different cooling rate, CCT diagram was obtained.

利用膨胀法结合金相-硬度法，在Gleeble-3800热模拟机上测定了27CrMo27S钢的临界点Ac1、Ac3以及Ms；测定了该钢在不同冷却速度下连续冷却时的膨胀曲线，获得了连续冷却转变曲线；研究了冷却速度对该钢组织及硬度的影响。

By dilatometric change and microscopic test, the critical point at Ac1、Ar1、Ac3 and Ar3 of ML40Cr steel was detemined in Gleeble-3800 the thermal-mechanical simulator. The continuous cooling transformation diagram of ML40Cr steel was obtained by measuring the expanding curves of different cooling rates. The mechanical property and transformation of austenite were analyzed. The proper range of control cooling rate about ML40Cr cold heading steel was found. All those provide the reference for productive practice to develop cold heading steel.

在Gleeble-380热模拟试验机上采用热膨胀法－金相法测定了ML40Cr钢的临界点Ac1、Ar1、Ac3、Ar3，同时测定了在不同冷却速度下过冷奥氏体连续冷却时的膨胀曲线，获得了该钢的连续冷却转变曲线；研究了ML40Cr连续转变冷却过程中奥氏体转变过程和转变产物的组织和性能，初步确定了ML40Cr盘条的控制冷却范围，为冷镦钢ML40Cr盘条的开发提供了参考依据。

On the other hand, the more important thing is because the urban housing is a kind of heterogeneity products.

另一方面，更重要的是由于城市住房是一种异质性产品。

Climate histogram is the fall that collects place measure calm value, cent serves as cross axle for a few equal interval, the area that the frequency that the value appears according to place is accumulated and becomes will be determined inside each interval, discharge the graph that rise with post, also be called histogram.

气候直方图是将所收集的降水量测定值，分为几个相等的区间作为横轴，并将各区间内所测定值依所出现的次数累积而成的面积，用柱子排起来的图形，也叫做柱状图。