查询词典 digital signals

The testing method comprises the following steps:(1) collecting the electrocardio-signal, the phonocardio-signal and the pulse signal of radial artery;(2) performing analog-to-digital conversion to the three signals to form the signal oscillogram;(3) identifying and extracting the characteristic point of each signal;(4) constructing the time series RR of electrocardio-period, the electromechanical delay time series and the pulse wave propagation time series of the combined variability index;(5) testing the validity of each time series;(6) calculating the heart rate variability, the electromechanical delay variability and the pulse wave propagation time variability; and (7) calculating the combined variability index of angiocarpy AV.

本发明提供了一种心血管系统联合变异性指标的检测方法和装置，检测方法包括以下步骤：(1)采集受检测者的心电、心音、挠动脉脉搏信号；(2)对三路信号进行模拟-数字转换，形成信号波形图；(3)识别和提取三路信号各自的特征点；(4)构造联合变异性指标的心电间期时间序列RR，电机械延迟时间序列和脉搏波传播时间序列；(5)检验各时间序列的有效性；(6)计算心率变异性、电机械延迟变异性和脉搏波传播时间变异性；(7)计算心血管联合变异性指标AV。

PFS3000 protective and fault information management system realizes transmission of protection information and oscillography files to master-control room, forwarding protection events as digital inputs to control and supervisory system, and receiving contact signals from control and supervisory system.

PFS3000 电网继电保护及故障信息管理系统（以下简称"青岩保护子站"）实现了保护信息和波形文件上传到主控室，将保护事件按遥信转发到监控系统，从监控系统接收转发过来的硬接点信号。

ABSTRACT Based on a summarization of the prevailing techniques for periodic signal measurements, the error sources in digital analyses and the latest progress in the research on reducing spectra leakage, through deep observation and analysis to some real world process phenomena, a novel concept of period domain analysis for process signals is firstly proposed in this dissertation.

基于对周期信号参量测试的发展、数字化分析的误差来源，以及减小频谱泄漏方面国内外的研究现状和发展方向的综述，通过对现实世界中某些过程信号的。。。

High detection sensitivity of 120 ppm can be achieved by using wave division mutiplexing technique, gas absorption cell with rectangular prism and digital match filter for the processing of weak signals which measurement accuracy of wavelength can be highly enhanced.

系统以ELED作为宽带入射光源，利用甲烷在光纤低损耗窗口波段的吸收特性，利用波分复用技术和直角棱镜吸收池，并采用提高波长检测精度的DMF对微弱信号进行处理，使得系统的灵敏度达到120 ppm。

It also needs to save, analyze and redisplay these signals. But traditional measuring instruments can't satisfy these requirements already. Digital oscilloscopes have little storage, few channels and weak analytical ability.

然而，采用传统的测量仪器已经不能满足要求，如果采用数字存贮示波器记录数据，也存在着存储深度不够、采样路数太少和分析处理功能较弱等问题。

The low frequency digital phase reflectoscope reflector in the industrial field is the general measuring tool which uses frequently, for instance the electrical network incorporation switches on when the electrical power system, requests two electrical network's electrical signals to be the same, between this request precise survey two power frequency signal phase difference.

低频数字式相位测试仪在工业领域中是经常用到的一般测量工具，比如在电力系统中电网并网合闸时，要求两电网的电信号相同，这就要求精确的测量两工频信号之间的相位差。

A DPC ( 300 ) includes: a frequency source ( 310 ) for generating a clock signal; a delay line ( 320 ) for receiving the clock signal and generating phase-shifted clock signals at output taps; a digital control device ( 330 ) for generating a control signal; and a windowing and selection circuit for generating the output signal, that includes sequential logic devices ( 500, 510, 520 ) and a combining network.

DPC(300)包括：频率源(310)，用于产生时钟信号；延迟线(320)，用于接收时钟信号并在输出抽头产生相移时钟信号；数字控制器件(330)，用于产生控制信号；以及开窗口与选择电路，用于产生输出信号，包括：时序逻辑器件(500、510、520)和组合网络。

The DSP ball counting unit respectively collects and comprehensively check the analog and digital two groups of signals to judge the ball and ball directions.

DSP过球计数单元分别采集并综合校验模拟和数字两组信号判断过球及过球方向。

If the filter's input and output signals are discrete-time, then the filter impulse response unit is also bound to be discrete, This filter called digital filter.

若滤波器的输入、输出都是离散时间信号，那么该滤波器的单位冲激响应也必然是离散的，这种滤波器称为数字滤波器。

Welding control system comprises hardware and software, using C language welding program, and it reduces difficulty of control system exploitation. Scheduling control, sampling disposal of feedback signals and digital PI modulation are achieved through program control, and this controls veraciously welding process.

焊接控制系统由硬件和软件两部分组成，焊接程序采用C语言编写，降低了控制系统软件开发的难度，通过程序控制实现时序控制、反馈信号的采样处理及数字PI调节，对焊接过程进行准确的控制。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。