查询词典 differentiating circuit

We further perfected hardware interface designs such as system main controlling circuit, signal measuring circuit and control box. Also, we have simplified system circuit and improved precision of adding water and controlling, simplifying operation and maintenance of system and increasing possibility of mass production.

进一步完善系统主控电路和信号测量电路以及控制箱的改造等硬件接口设计，精简系统电路布局结构，提高系统的加水控制精度和操作的方便性，同时提高了系统的可维护性、批量生产的可能性。

In this paper, the design of a simple, low-cost walkie-talkie circuit and main circuit of the key components of the circuit is introduced

本文设计了一种简易、低成本的对讲机电路，对关键电路及主要的电路元件做了介绍。

The IGBT-controlled chopper circuit can be greatly simplified as the smoothing inductor and commutation circuit of the thyristor-controlled chopper circuit are no more required.

文中提出了以IGBT、二极管、电阻和电解电容等四个元器件组成的斩波电路，经实验和仿真证明不仅能有效地调节转子电阻，而且同时兼有IGBT关断吸收电路的作用，能显著改善IGBT的关断轨迹。

What's more, the typical application circuit of UC3843 has been simplified , especially the feedback, compensation circuit and the snubber circuit.

此外，还对UC3843典型运用电路进行了简化修改，特别是反馈补偿电路以及吸收回路。

The main content of this thesis is as follows: 1The structures of EPS are analyzed. The main components of EPS are introduced in detail. Then the distributed torque in EPS is analyzed and the control system model is set up. 2Three control modes are discussed and the control strategy of EPS is studied in detail. Three principal modules in the control strategy are discussed—the predicted module which predicts motor rotational speed and steering rotational speed, the power-assistant module and the return control module. 3The assistant torque curves of the motor are designed by using the B-spline, so that any kind of custom-built assistant torque curves can be designed according to different kinds of automobiles. 4The hardware frame of EPS is studied. The developed controller based on 8-bit MCU MC68HC908MR8 is introduced and many related circuit units are designed, including the control circuit, the driver control circuit and so on. The software structure is discussed, then the steering control program flowchart is given.

本文的主要工作有： 1分析了EPS 的总体构成，对EPS 的各个部件作了详细的介绍，并在此基础上分析了EPS 的受力情况，建立了控制系统模型，并研究了EPS 的安全性能； 2讨论了EPS 的三种控制方式，提出了控制策略，并讨论了其中三个关键模块的作用：预估模块包括对电机转速和方向盘角速度的预估，助力控制模块以及回正模块； 3用B 样条插值方法进行EPS 助力曲线的设计，可按照用户的要求设计任意形状的助力曲线，以满足不同车型和不同用户的要求； 4研究了控制系统的硬件结构，以MC68HC908MR8 为核心设计了控制器，详细讨论了控制器的控制电路、驱动电路等；设计了控制系统的软件，给出了控制程序流程图，并对要点进行了详细的说明。

Trigger circuit by adjusting the phase of the trigger pulse to control the on-off thyristor, which can be manually controlled to adjust the output voltage, and then, after step-down transformer can be used to obtain the magnetization of the magnetic low-voltage high-current power supply, mainly by the SCR the main voltage regulator circuit, trigger circuit, such as composition, is a broad application prospect of the exchange regulator controller.

通过调节触发电路的触发脉冲的相位来控制晶闸管的通断，从而控制输出得到可人工调整的电压，再经过降压变压器得到可用于磁化的低压大电流磁化电源，它主要由可控硅调压主电路、触发电路等组成，是一种具有广阔应用前景的交流调压控制器。

And then, the contiunous current modeof this circuit is discussed, and the PWM circuit and over-current -protection circuit are designed. At the same time, the calculation methods of storage inductance, output capacitor and sampling resistor are given.

讨论电路的电流连续工作模式，设计了电源的脉宽调制电路和过流保护电路，并给出了蓄能电感、输出电容和输出电压取样电阻的确定方法。

A time-shared control circuit points to multiplexer, applies the control signal and switches and repeats to output the input signal by the predetermined cycle order. A comparator compares the voltages of the output signal from the multiplexer and the reference voltage and outputs a dimorphic signal representing the comparative result. A time-share controlled circuit applies the control signals, controls the action of the multiplexer and the latch circuit to lead the respective voltage comparative result to be maintained in the latch circuits.

分时控制电路(5)对多路调制器(4)，使用控制信号(Sc1)，以所定周期顺序切换反复输出所输入的信号(St1)-(St4)，比较器(3)对从多路调制器(4)输出的信号的电压和基准电压进行电压比较，输出表示该比较结果的二态信号，分时控制电路(5)使用控制信号(Sc1)及(Sc2)，控制多路调制器(4)及闩锁电路(LT1)-(LT4)的动作，使得信号(St1)-(St4)的各电压比较结果分别保持在闩锁电路(LT1)-(LT4)中。

The choice of the transformer includes: Main transformer use the main technique in number, capacity, model number...etc. in set data of the transformer to really settle; The electricity lord connected the line to introduce primarily the electricity lord connects the linear importance, design according to, the basic request, every kind of merit and shortcoming and lords that connect the line form connects the linear choosing more, the lord that combine to establish the in keeping with my plant the request connects the line; The short-circuit galvanometer is regarded as the most important link, this thesis introduced the calculating purpose in short-circuit electric current, assumption term, general provision, the calculation, network transformation of a parameter detailed, and each calculation etc. knowledge that short circuit order; The choice of the high pressure electricity equipments includes the mother line, high pressure breaks the road machine and insulate the switch, electric current to feels with each other the machine, electric voltage feels with each other the choice principle of the machine, high pressure switch cabinet with request, and proceed to these equipments the school check with the related introduction in product.

变压器的选择包括：主变压器的台数、容量、型号等主要技术数据的确定；电气主接线主要介绍了电气主接线的重要性、设计依据、基本要求、各种接线形式的优缺点以及主接线的比较选择，并制定了适合要求的主接线；短路电流计算是最重要的环节，本论文详细的介绍了短路电流计算的目的、假定条件、一般规定、元件参数的计算、网络变换、以及各短路点的计算等知识；高压电气设备的选择包括母线、高压断路器、隔离开关、电流互感器、电压互感器的选择原则和要求，并对这些设备进行校验和产品相关介绍。

And experiment was based on the simulation, the results show that charge circuit and uplifted circuit both was adopted the same circuit, which can realize energy bi-directional flow, also have low switch ullage and high dynamic response.

在此基础上进行了实验研究，仿真和实验结果表明，该装置升压和降压只采用同一个主电路，即可实现能量的双向流动，且具有低开关损耗和较高的动态响应。

Methods Clinical data of 3 cases of bile duct injury during laparoscopic cholecystectomy were analyzed retrospectively.

回顾总结3例LC术中胆管损伤的临床资料，分析3例胆管损伤的原因及对策。

These techniques are applied to the gobang.

本文将这些技术用于五子棋中。