查询词典 differential circuit

Product characteristics : 1, excellent heat resistance : can adapt to the use of power lines due process overload and short circuit of the high temperature; 2, excellent electrical properties : material for the performance of their higher intensity and volume resistivity of insulation, security is good; 3. excellent corrosion resistance and anti-aging properties : apply to the soil and working environment, long life; 4. excellent flame retardance : difficult combustion; 5, smooth wall formation, the friction coefficient, good wear resistance : in the installation process can greatly reduce the damage to power lines, improve work efficiency; with the traditional asbestos cement pipes, the The product is light weight, good flexibility, earthquake-resistant and differential settlement, and not at the construction site encapsulation pouring concrete; Transport construction is simple, low cost, can greatly shorten the construction period.

产品特点： 1、优良的耐热性能：能适应电力电缆使用过程因过载短路而产生的高温； 2、优良的电气性能：材料自身表现为较高绝缘强度和体积电阻率，安全性好； 3、优异的耐腐蚀性能和抗老化性能：适用于各种土壤和工作环境，使用寿命长； 4、优良的阻燃性能：不易燃烧； 5、内壁光滑平整、摩擦系数小，耐磨性能好：在敷设过程中可大大降低对电缆的损害，提高工作效率；与传统的石棉水泥管相比，产品的重量轻、柔性好、抗震性及抗不均匀沉降好，无须在施工现场包封浇混凝土；运输施工简便，费用低，可大大缩短工期。

In the analysis of the circuit, the differential equation based on the theory of electromagnetism had been established; the circuit qualitatively had been analyzed, and the current on the coil in the process of experiment had been calculated.

在电磁压制放电电路的模拟分析中，基于电磁学理论建立了放电过程的微分方程，对电路作了定性的分析；通过对实验参数的模拟，求解出实验过程中线圈上的载荷电流。

In this thesis, we have successfully utilized the combination of MOS and HBT to design negative differential resistance circuit, which is called as MOS-HBT-NDR circuit.

在本论文中，我们已经成功利用MOS与HBT的组合来设计负微分电阻电路，我们称此负微分电阻电路为MOS-HBT-NDR电路。

According to pulse oddment counting principle, a pulse signal counting circuit for differential ring lasers is designed based on XC3S400AN, a kind of FPGA chip with high performance. The structure of the circuit is described in VHDL language and realized through sequence control and synchronization process of high accuracy/frequency clock signal.

根据脉冲零头计数原理，应用高性能的FPGA芯片XC3S400AN，基于VHDL结构描述语言，对高精度高频率时钟信号进行时序控制及同步处理，设计出一种四频差动激光陀螺脉冲信号计数电路，并进行了实验测试。

The Periscope Drawtube will be bent because of the water resistance in sailing and this bend will cause the error of star measurement. Due to its especial structure, contactless measurement is the only way to measure its bend degree. First this paper introduces the method by linear array CCD based on structure and light path; Second it expatiates linear array CCD work principle and driving scheduling with example of TCD1501C and the driving circuit by CPLD. The output signal of linear array CCD includes common disturbance so the differential amplifier is needed. In order to make the signal adapt to computer processing, a threshold circuit with Schmitt characteristic and the data process following threshold are given. At last, some key problems in application are given.

潜艇潜望镜的镜筒在航行时受到水的阻力会产生弯曲变形，这种变形会造成潜艇对星体测量的误差；由于镜筒结构的特殊性，对其弯曲程度的测量只能采用非接触方法；首先从结构和光路方面介绍采用线阵CCD作为检测元件实现对镜筒弯曲程度的测量；其次以东芝公司的线阵CCD（TCD1501C）为例阐述了其工作原理及驱动时序的控制要点，并介绍了基于可编程逻辑器件的线阵CCD的驱动电路；线阵CCD输出的信号中含有共模干扰，必须采用差分放大器将其抑制；为将信号转化为适合计算机处理的数字信号，文中给出了有一定实用价值具有施密特特性的二值化处理电路及二值化后的数据处理过程；最后阐述了在实际使用中的一些关键问题。

Differential amplifier and negative feedback circuit realize SAW drive circuit gain together.

差分放大级与负反馈放大器配合使用共同实现电路的增益。

On the basis of the analysis and comparison of some sensors, Eddy Current Sensor is selected, and its equivalent circuit, strength and depth of the eddy current, radial distribution of the current, axile intensity of the magnetic inductorium are all analyzed. The processing circuit of sensors signal is designed. Because of coupling problem of the sensors, differential measurement of sensor is applied.

在分析比较各种传感器特性的基础上，选择了电涡流传感器作为转子位移的检测元件；分析了电涡流传感器的等效电路、涡流强度和深度、涡流的径向分布、线圈轴上的磁感应强度；设计了传感器的信号处理电路；对于传感器始终存在的偏置耦合问题，提出了传感器差动测量的方法。

Three elements should be calculated in first-order circuit, which can synthesise analytical solution. Second-order series RLC and parallel RLC both can be calculated by the general function, which uses the Matlab to calculate differential equations. Generally, second-order and high-order circuits use Laplace transformation to formulate circuit equation, and get analytical solution by using Laplace inverse transform.

一阶电路先计算3要素，后合成解析结果；RLC串联和并联的二阶电路采用自编的通用函数计算，自编函数采用了Matlab求解微分方程的符号运算方法；一般的二阶电路和高阶电路采用拉氏变换列写电路方程，再用拉氏反变换得到解析结果。

In order to carry constant current bias amplifier and to raise the precision of the differential amplifier of the voltage amplification stage, an overly highly precise constant current circuit is adopted as the bias circuit used as criteria of operation, and the supply voltage variation supression ratio is raised much more.

为了执行恒流偏置放大器和提高精度的差分放大器的电压放大阶段，过于高精度恒流电路采用为偏置电路用来作为标准的运作，以及电源电压的变化抑制比筹集更多。

At present, OTA circuit is designed the best circuit with minimum error generally acknowledgedly, and possessed three following advantages at the same time: using single-ended-input OTAs (overcoming the feed-through effect due to the use of differential-input OTAs), using grouded capacitors (absorbing the shunt parasitic capacitance), and using the minimum components and all the parasitic capacitances have the same places as those of all the given capacitors in the realized circuits.

目前为止，OTA电路是被公认设计最佳且误差最小的电路，且同时具备了以下三项优点：(1)使用单端输入的OTA(可免除寄生电容的Feed-through效应)，(2)使用接地电容，(3)使用最少的主动元件，且所有外加电容位置恰好与所有寄生电容的位置相同，吸收了寄生电容，并减少寄生效应对整体电路的影响。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐