查询词典 diesel engine with antechamber

To validate the FEM calculations of the cylinder block of a six-cylinder in-line diesel engine,the dynamic strain-stress and temperatures of the main bearing wall s and caps were measured on engine testbed with strain-gauge and resistance thermometer.

为评估某直列6缸柴油机缸体有限元强度分析结果，采用应变电测法实测了该发动机缸体上可能的危险部位主轴承座、主轴承盖动态应力以及这些部位的温度。

And it is a full electrical control diesel engine equipped common rail fuel system. The driving motor and engine are correspond controlled via CAN bus, using the load leveling concept and logic threshold approach to control the torque distribution,various operation modes and the dynamical transitions between the modes for hybrid power train.

通过CAN总线实现了联合控制，用基于负荷平衡和逻辑门限的实时控制策略，实现了混合动力系统的转矩分配和不同工作模式以及模式间的切换。

The pressure variations in diesel engine cylinders indicate the combustion s tates of the engine.

根据柴油机在不同状况下燃烧过程中气缸的压力波动情况进行了模式分类。

With its effortless refined turbo diesel engine matched with a dynamic chassis plus a good 6 speed transmission, the S80 brought out superior on road motoring behaviour. It whiskered corners and bends competently, a keen driver will not be disappointed with its ability in excellent body control and mid-corner adjust ability. Not to mention with its excellent fuel economy on highway cruising. The wind and engine sound were minimal, and you can just concentrate on listening to its on board premium sound system.

S80是Volvo车厂精心的为过去，现在及未来的顾客研制的大师级作品，它与福特及越野路华共用一个汽车底盘，而经由Volvo厂方自己再调校，使它比越野车Freelander的底盘更强5个百分比，这个Dynamic Chassis底盘可以不断的监察汽车的反应，以抑制器快速的回应汽车的驾驶情况，并抗衡汽车在强大的加速，极端的制动及快速的转向所造成的俯仰，前潜及翻滚等反应，而它亦配上舒适，运动及先进的选择模式，这些科技帮助驾驶者及乘客取得优良的驾车及乘车经验。

In combustion simulation , multi-zoons model for diesel engine and two zoons model for gasoline engine are described.

介绍汽油机的准维两区计算模型和柴油机的准维多区模型，讨论模型对排放的预测方法。

When the diesel engine idles, engine oil pressure should not be less than 0.1MPa.

柴油机正常运转时，机油压力应在0.3～0.6MPa之间。

Sensors, data acquisition cards and virtual instrument software are applied in the electronic control of ethanol injecting for optimized diesel/alcohol dual-fuel engine, through complement factor experiment which combines three fuel supply advance angle with four ethanol supply time, the performance of dual-fuel engine is compared with the original one under same condition.

使用传感器、数据采集卡和虚拟仪器软件改进柴油/乙醇双燃料发动机的乙醇喷射电子控制系统，通过三个供油提前角、四个供醇时刻组合的全因素试验，比较了双燃料发动机与原机相同工况下的性能。

The assembly of journal and plain bearing liner space is too little, force of organic still oil pressure is small it is the crucial index that affects lubricant result, make lubricate because of lacking engine oil between crankshaft and plain bearing liner and bite dead invalidation, include to be pulled badly, lack lube, layer of alloy of dry attrition generation is fused, grind sliding surface to did not maintain the oily film of certain ply, and all sorts of local overload exhaustion are destroyed, cavitation erosion and V form are destroyed etc, through technology of him director diesel locomotive old experience reachs the analysis of pair of its breakdown reasons, put forward precautionary measures especially. As a result of,the burns caustic mechanism plain bearing liner to burn caustic mechanism of 1 plain bearing liner is the lube film burst between journal and plain bearing liner, cause plain bearing liner and crankshaft generation clash, below high temperature, high pressure and high rotate speed, the wear-resisting alloy layer of plain bearing liner wears away prematurely or fuse, cause plain bearing liner and crankshaft to stick thereby bite, can make the steel back of plain bearing liner and Kong Zhong produces whirligig, inlet port is jammed, carry on the back by steel again with the friction of aperture causes high temperature to make plain bearing liner burned-out further, can cause bolt to break off, happen swing a malign accident that pounds cylinder body of bad internal-combustion engine.

轴颈和轴瓦的装配间隙太小，还有机油压力低是影响润滑效果的关键指标，使得曲轴和轴瓦之间因缺少机油润滑而咬死失效，包括严重拉伤，缺少润滑油，干摩擦产生合金层熔化，磨滑面没有保持一定厚度的油膜，以及各种局部过载疲惫破坏，气蚀和V形破坏等，通过本人主管内燃机车技术多年经验及对其故障原因的分析，特提出预防办法。1轴瓦的烧损机理轴瓦烧损的机理是由于轴颈和轴瓦之间的润滑油膜破裂，导致轴瓦和曲轴产生摩擦，在高温、高压和高转速下，轴瓦的耐磨合金层过早地磨损或熔化，从而引起轴瓦和曲轴粘咬，会使轴瓦的钢背和座孔中产生旋转运动，进油孔被堵塞，再由钢背和座孔的磨擦进一步引起高温使轴瓦烧坏，并会造成螺栓折断，发生甩出捣坏内燃机缸体的恶性事故。

With CAD/CAM integrated modeling technology and NC programming manufacturing to develop cold box process casting technology of engine cylinder block and cylinder head of linear four-cylinder,two-air valve mid-position cam,four-stroke direct-jet combustion chamber,drying cylinder sleeve turbocharged and oil intercooled diesel engine in accordance with EUROⅢ standard of automobile tail gas exhaust.

运用 CAD /CAM一体化复合建模与数控编程加工技术，研究开发了符合欧Ⅲ汽车排放标准的直列四缸、二气门中置凸轮、四冲程直喷燃烧室、干式缸套涡轮增压和机油中冷式柴油发动机缸体缸盖冷芯盒铸造成形工艺。

Acknowledge that the following practical cycles can be heat engine cycle of ideal gas, such as the internal combustion engine , Diesel cycle , Brayton cycle.

了解并掌握内燃机和燃气轮机装置的实际工作循环可抽象为理想气体的热机循环。

More direct, directer ; most direct, directest

径直的，笔直的

Do you know how to use a chain saw?

你知道如何使用链锯吗？