查询词典 die-off

Fewer animals will die during warmers winters, but greater numbers will die during hotter summers.

很少有动物因为暖冬而死去，但是却有大量的动物会因为夏天过热而死。

Fewer animals will die during warmers winters, but greater numbers will die during hotter summers.

一些动物会在暖冬死去，更多数量的会在炎夏发生。

Company employees more than 150 people, has a history of more than 10 years of printing and packaging printing the books and professional factories, to undertake various types of foreign trade of goods produced in large, medium and small packaging, as well as invitation cards, calendars, the Chinese New Year cards, books, magazines , And other printed products, and through the German TUVISO-9001 quality certification from Germany with the introduction of the souvenir sheet colored Offset, Japan Komori four-color offset press, a souvenir die-molding machine, and other contemporary first-class equipment and a plastic Tuyin , Bronzing, the ripples die-indentation, convex pressure, binding, and so the full set of domestic advanced process equipment design is strong, superb techniques, products, winning several times in the industry, users enjoy high reputation.

公司现有职工150余人，是一家拥有十余年历史的包装印刷和书刊印刷的专业工厂，承接印制内外贸各类商品的大、中、小包装，以及请柬、挂历、贺年卡，书刊，杂志等印刷产品，且通过了德国TUVISO—9001质量认证；拥有从德国引进的小全张五色胶印机、日本小森四色胶印机，小全张模切成型机等当代一流设备，并拥有胶凸印、烫金、波纹、模切压痕、凹凸压、装订等国内先进的全套工艺设备；设计力量雄厚，技艺精湛，产品多次在行业中获奖，在用户中享有较高的声誉。

To die together with the release铁盖burning furnace used in hot, brush with oil dip coated mold hole again, check铜壶will be followed by injection mold slurry surface hole (only half-filling holes), will die immediately give onwards, slowly turning to face sticky paste evenly in the hole wall, and then on the furnace will be inserted into holes in the bamboo pulp surface scraping the walls of the hole.

把模具连同铁盖放炉上用中火烧烫，用刷子蘸水油将模具孔涂抹一遍，取铜壶将面浆依次注入模孔，随即将模具举起，缓缓转动，使面浆均匀黏在孔壁，然后放在炉上，将竹片插入孔中把面浆刮向孔的四壁。

Die lands should be 3-5 times the dimension of the die opening;entrance angles to the land should be as

模具面积应是模槽尺寸的3-5倍；入口角的度根据特殊情况考虑，尽可能小而实用，但是， 10 °-60 °是常见的。

The occurrence of wrinkling is attributed to the large die gap, which is the difference between the side length of the die cavity opening and the side length of the punch head.

出现的皱折是由于模具间隙大引起的；该间隙在模具腔口的侧面距离和冲头侧面距离之间有差别。

The operating noise is lowered greatly, and the opening and locking die vibration reduced; the service life of equipment and die is prolonged, and working environment improved

注塑机运行噪音明显降低，开、锁模振动减轻，延长设备和模具的使用寿命，改善工作环境。

It is suggested that the wrinkling is due to the large unsupported area at the draw wall during the stamping process, also, the side length of the punch head and the die cavity opening are different owing to the die gap.

它暗示起皱是由于拉伸过程中存在大的无支持区域，而且，冲子头部的边长和模腔的打开也由于模具间隙而不同。

Using the finite element method and based on finite element simulation of profile extrusion process, the effect of local extrusion ratio, die land area and the distance between extrusion cylinder center and die opening center on mental flow velocity is studied. The deformation flow laws on profile extrusion process are obtained.

本文采用有限元方法，以型材挤压过程的有限元模拟为基础，研究了局部挤压比、挤压带面积和模孔距离对金属流动速度的影响，获得了型材挤压过程的变形流动规律。

Barlat1989 is recommended owing to its computational effectiveness. The technique is given using the dynamic relaxation method to obtain the steady position of the blank inside die opening line from end of holder forming stage to start of die forming stage.

在板料成形过程的数值模拟研究中，提出了将动力松弛法用于获得压边圈成形结束到凸模成形开始之前凹模开口线内板料的稳定位置，从而消除动力效应的处理技术。

And Pharaoh spoke to Joseph, saying, Your father and your brothers have come to you.

47：5 法老对约瑟说，你父亲和你弟兄们到你这里来了。

Additionally, the approximate flattening of surface strip using lines linking midpoints on perpendicular lines between geodesic curves and the unconditional extreme value method are discussed.

提出了用测地线方程、曲面上两点间短程线来计算膜结构曲面测地线的方法，同时，采用测地线间垂线的中点连线和用无约束极值法进行空间条状曲面近似展开的分析。