查询词典 die-hardism

Sweet rose,whose hue angry and brave,Bids the rash gazer wipe his eye,Thy root is ever in its grave,And thou must die,Sweet spring,full of sweet days and roses,A box where sweets compacted lie,My music shows ye have your closes, And all must die,Only a sweet and virtuous soul,Like season''''d timber,never gives;But though the whole world turn to coal.

美丽的玫瑰，色泽红润艳丽，令匆匆而过的人拭目而视，你的根永远扎在坟墓里，而你必须消逝。美妙的春天，充满了美好的日子和芳香的玫瑰，如一支芬芳满溢的盒子，我的音乐表明你们也有终止，万物都得消逝。唯有美好而正直的心灵，犹如干燥备用的木料，永不走样。

Drill, tap, die, tap and die sets, cutting tools.

8D58 8D60 钻头，丝锥，板牙，及套装类五金工具，及切削工具。

Company may in accordance with the metric system, British, American, German standard and other tools to create common standards of international production processing, the main products are die, hand tap, machine tap, and the combination of suit, an annual output of all kinds of varieties of different specifications of the tap, die up to 20 million more, various combinations of thread tools package for more than 300,000 sets.

公司可根据公制、英制、美制、德标等各种国际工具制造通用标准生产加工，主打产品为板牙、手用丝锥、机用丝锥、及其组合套装，年产各类品种规格的丝锥、板牙达2000万件以上，各种组合套装螺纹工具30万套以上。

Springback isconsidered in the design of the bending die ,since there is a big bending radius .The thirddie is wedge clicker die .

第二副模具为弯曲模，由于有一个较大的弯曲半径，所以在设计中主要考虑回弹因素对成形精度的影响。

Based on gaining high productivity and the high percentage of material consumption,We made the choice of using two dies to fulfill the design: one progressive die to execute punching, drawing and blanking.we use the second bending die with a wedge to get the two bends.

本设计以提高生产率及材料利用率为出发点，采用两套模具进行该启瓶器的设计：第一套级进模完成冲孔、拉深和落料；第二套模具为楔块式弯曲模，用来完成两次弯曲成形。

Also new is the CF die-cast aluminium swingarm, which is manufactured using Yamaha's patented CF die-casting technology, a system that has opened up new possibilities in aluminium chassis design.

也就是新的CF压铸铝swingarm ，这是制造过程中利用雅马哈的专利比照压铸技术，制度，开辟了新的可能性，在铝合金底盘的设计。

The design of panel drawing die surface is the key process of panel drawing die, and it is also the key factor on the development of panel products.

覆盖件拉延模工艺型面的设计，是覆盖件拉延模设计的中心环节，也是影响覆盖件产品开发的重要因素。

Occurs when the semi-finished, warping, especially the post-mounted corrugrted semi-finished products, immediately after the closing of embossing plate, on the paper--and there is no uniform die to tilt paper with the sponge rubber or contact, so easily make embossing plate produced by 印张 bliding, die-cutting production phenomenon.

当半成品出现卷曲、起翘情况时，特别是经过裱贴以后的瓦楞纸板半成品，放在压印平板上合压时，纸面与模切版没有均匀接触，使翘起的纸面先与版面上的橡胶条或海绵接触，这样容易使压印平板上的半成品印张产生滑移现象，造成产品模切不准。

First, most of the magnetic properties of the die-cutting machining needs a secondary operations or an exhaust box, this is it is different from entity die iithography.

第一，不小局部磁性模切版的模切增工必给一个补助工序或一个排宝箱，这是它差别于实体模切版增工的方面。

If we are like kernels of wheat fall to the ground and die, we will produce many seeds that each of the seeds will also have an opportunity to live and to die for the Lord.

如果我们像麦子一般落在地里死了，将有许多子粒因我们的死而被结出，且每一个子粒将有机会为主而活和为主而死。

They weren't aggressive, but I yelled and threw a rock in their direction to get them off the trail and away from me, just in case.

他们没有侵略性，但我大喊，并在他们的方向扔石头让他们过的线索，远离我，以防万一。

In slot 2 in your bag put wrapping paper, quantity does not matter in this case.

在你的书包里槽2把包装纸、数量无关紧要。