查询词典 die of

Both ends of the die cutting knife vrachyaxis are used with hole Loy, wood box fixed to prevent transportation die-cutting knife inter-articular in the box.

模切刀两头的长轴需不分别用带孔的木块套上，木块在箱边固不退，制止输送洋模切刀在箱边移位。

The GR2 series Crucible Lead-melting Electric Furnace is a sort of energy-saving Melting Electric Furnace, it is mainly used for melting lead, lead liquid insulation , quantitative die casting ,matching with die casting machines and producing electrical storage bottles.

GR2系列坩锅熔铅电炉系节能型熔化电炉，主要供熔化铅，铅液保温，定量压铸，与压铸机配套，用于制造蓄电瓶等。

To die together with the release铁盖burning furnace used in hot, brush with oil dip coated mold hole again, check铜壶will be followed by injection mold slurry surface hole (only half-filling holes), will die immediately give onwards, slowly turning to face sticky paste evenly in the hole wall, and then on the furnace will be inserted into holes in the bamboo pulp surface scraping the walls of the hole.

把模具连同铁盖放炉上用中火烧烫，用刷子蘸水油将模具孔涂抹一遍，取铜壶将面浆依次注入模孔，随即将模具举起，缓缓转动，使面浆均匀黏在孔壁，然后放在炉上，将竹片插入孔中把面浆刮向孔的四壁。

Die lands should be 3-5 times the dimension of the die opening;entrance angles to the land should be as

模具面积应是模槽尺寸的3-5倍；入口角的度根据特殊情况考虑，尽可能小而实用，但是， 10 °-60 °是常见的。

The operating noise is lowered greatly, and the opening and locking die vibration reduced; the service life of equipment and die is prolonged, and working environment improved

注塑机运行噪音明显降低，开、锁模振动减轻，延长设备和模具的使用寿命，改善工作环境。

It is suggested that the wrinkling is due to the large unsupported area at the draw wall during the stamping process, also, the side length of the punch head and the die cavity opening are different owing to the die gap.

它暗示起皱是由于拉伸过程中存在大的无支持区域，而且，冲子头部的边长和模腔的打开也由于模具间隙而不同。

The thesis presents a practical die structure with angle pin and gear shaft and rack for secondary combined inclined down loosing core of die casting hopper bodies.

本文给出了浮子室体铸件斜销-齿轴-齿条二级联合斜下抽芯压铸模实用结构，论述了模具结构特点和工作过程。

The drawing die structure of aluminum foil snack box and marginal pressure design program are introduced, the die structure is complicated.

介绍了铝箔快餐盒拉伸模结构及压边的设计方案，此模结构较复杂。

The die construction , running principle and features technological process flow , technique parameters and product performance of aluminum alloy integral naves by gravity die casting are described

阐述了金属型铸造摩托车铝合金整体车轮的模具结构，工作原理及特点，铸造工艺流程，工艺参数及产品性能。

According to provide mapping products parts Die Casting plans and three-dimensional map or a few die, casting process for the preparation of programmes and heat treatment, trial production mold, repair mode, guiding the production process and to promptly resolve problems or feedback at the scene, casting the test or correction, study Existing problems and proposed solutions, until the qualified products and delivery.

根据用户提供产品零件图绘制铸件图及模具图或三维数模，编制铸造工艺方案及热处理方案，试制模具、修模，指导生产过程并及时解决或反馈现场问题，对铸件进行检验或校正，研究存在问题并提出解决方案，直至产品合格并交货。

Singer Leona Lewis and former Led Zeppelin guitarist Jimmy Page emerged as the bus transformed into a grass-covered carnival float, and the pair combined for a rendition of "Whole Lotta Love".

歌手leona刘易斯和前率领的飞艇的吉他手吉米页出现巴士转化为基层所涵盖的嘉年华花车，和一双合并为一移交&整个lotta爱&。

This is Kate, and that's Erin.

这是凯特，那个是爱朗。