查询词典 die of

There are six forming methods throughcombining three different types of elements, among them, thereare four forming methods which have emblematize andpracticability: multi-point die forming、half multi-point die forming、multi-point alternating forming、half multi-point alternating forming.

对有限元模型建立及数值模拟关键算法和参数的研究在进行薄板类件多点成形的有限元分析中，涉及两类边界条件，一类是载荷，另一类是运动约束。

We are specializing in manufacturing ES series Folder Gluer,ETH series Laminator,BC series Die-cutting machine and Holographic Foil Stamping and Die-cutting machine etc.Our company gained the certificate UKAS ISO 9001:2000 in 2006, and we practice the principle of "quality for survival, innovation for development , pursuit the excellent quality, and strengthen the system management".

主要生产制造ES系列糊盒机、ETH系列裱纸机、BC系列模切机及全息防伪烫金模切机等产品。2006年通过&UKAS&ISO9001：2000国际质量管理体系认证，秉承&以质量求生存，以创新求发展；追求卓越质量，强化系统管理&为宗旨。

Diamond die. Heterotypic various non-standard mold and die under the special requirements of users and technical guidance, develop new products.

金刚石模。各种异型模及非标准件模具可根据用户特殊要求与技术指导，开发新产品。

One of Schuman's works,"op.48, Dichterliebe", and Schubert's "Winterreise","Die Schone Mullerin", and "Op.103(1803)Swan song" three works, and also some Schubert's known pieces, including "Erlkoenig" and "An die Musik", that shows audiences different opera performance.

内容有舒曼的联篇歌曲〝诗人之恋〞，及选自舒伯特〝冬之旅〞、〝美丽的磨坊少女〞、〝天鹅之歌〞三大联篇的选曲，还有舒伯特著名曲目《魔王》、《音乐颂》等，听众可藉此感受不同於歌剧形式的表现张力。

When solder bumps (22) on the die are reflowed, the fluxing agent acts to remove any oxides present on the solderable surfaces of the substrate or the die.

当管芯上的焊料突点（22）被回流时，该助焊剂的作用是清除基板或管芯的可焊接表面上存在的任何氧化物。

Die edge bevel edge fangzheng, existing is not enough, the tightening of the vulnerable after starting kungsi, die tightening, and embossing plate the local deformation, edgwise, and so on will line indentation.

模切版边缘不够方正、存在斜边情况时，紧固后的版容易出现起弓现象；模切版的紧固过度，以及压印平板上的铁板局部出现变形、起弓等情况，都会造成压痕线爆裂。

Piercing blanking die design must die so that the pressure of the press center and the centerline coincides slider.

冲孔落料模具的设计必须使冲模的压力中心和压力机的滑块中心线相重合。

The design method of faceplate oblique edge blanking die, die structure, punch structure and matrix structure were introduced in detail.

详细介绍了面板斜刃冲裁模的设计方法和模具结构及冲裁凸凹模结构。

We need two sets of parts forming mold, one is a drawing blanking punching die, flanging die is another.

零件的成形需要两套模具，一套是落料拉深冲孔的复合模具，另外一套是翻边模具。

Without prejudice to the die-cutting quality, reduce the height of the die cutting back your funds.

在不感化模切质量的环境下，贬低模切刀刀不背的矮度。

Singer Leona Lewis and former Led Zeppelin guitarist Jimmy Page emerged as the bus transformed into a grass-covered carnival float, and the pair combined for a rendition of "Whole Lotta Love".

歌手leona刘易斯和前率领的飞艇的吉他手吉米页出现巴士转化为基层所涵盖的嘉年华花车，和一双合并为一移交&整个lotta爱&。

This is Kate, and that's Erin.

这是凯特，那个是爱朗。