查询词典 die of

Comparting fatigue tests on TR upsetting and open die forging,this paper finds that the fatigue strength of the TR upsetting crankshaft is 16 — 22 percent higher than that of the open die forging crankshaft.

本文介绍了先进的TR镦锻法制造曲轴毛坯的工作原理。

The election of press process is based on consulting correlation datum and analyzing the form of manufactured product meticulous; The election of press die is based on synthesis considerations on economical efficiency、the processing property of part and complex degree iso many factors; Calculating the work blank of manufactured product unfold dimension is lined feed on the premise of calculation convenience but without contribution die confectioning simplified frequent application cast.

冲压工艺的选择是经查阅相关资料和和对产品形状仔细分析的基础上进行的；冲压模具的选择是在综合考虑了经济性、零件的冲压工艺性以及复杂程度等诸多因素的基础上进行的；产品毛坯展开尺寸的计算是在方便建设又不影响模具成型的前提下简化为所熟悉的模型进行的。

Then you might even die on a cross, so as not to be different from the Master, but you will die for whoever crucifies you, and so love will have the ultimate victory.

最后，也许你甚至会死在十字架上，效法你的『师傅』。可是你要为那钉你在十字架上的人而死，如此，爱将会获得最终的胜利。

The process features and shape features of the electronic part are classified and defined, and then the feature model library is built, which enables rapid input of the part information. The rules and methods of stamping process design are summarized to build the stamping process library, so that the stamping process can be designed rapidly and intelligently. Furtherly, the process design rules and methods in process station layout of multi-station progressive die as well as the methods of decompounding and compounding process and the expression method of the process station layout are concluded and summarized, and then the rule library and case library of process station layout are built. Designing the process station layout rapidly is carried out based on rules and cases. At last the rapid design function of process station layout is validated through simulating the rapid designing layout system of multi-station progressive die on Pro/E 3D platform.

主要研究成果有：对电子产品冲压件的工艺特征与形状特征进行了分类和定义，建立了特征模型库，实现了冲压件信息的快速输入；归纳了冲压工艺设计规则和方法，建立了冲压工艺知识库，实现了冲压工艺快速与智能化设计；归纳总结了多工位级进模工步排样中的工序设计原则和方法，工序分解与工序组合方法，工步排样知识的表示方法，建立了工步排样规则库和实例库，利用基于规则和实例的推理方法，实现了工步排样的快速设计；在Pro/E三维软件平台上开发了电子产品多工位级进模工步排样快速设计系统，系统通过实例验证了工步排样的快速设计功能。

Mr Guo thinks, the caption after Sohu net is changed and the thematic photograph that report formerly are contrary to, its do sth without authorization changes the behavior of caption to make the audience of numerous and unidentified truth and netizen produce erroneous impression, small swallow of the person that think to die is to love another person, derogated reputation of the person that die, cause huge spirit harm and negative effect to them.

郭先生认为，搜狐网更改后的标题与原报道的主题相悖，其擅自改标题的行为使众多不明真相的观众和网民产生错误印象，认为逝者小燕是移情别恋，贬损了逝者名誉，给他们造成极大的精神伤害以及负面影响。

Compared with even die-drawing, camber die-drawing's limit drawing coefficient is detracted, so efficiency is increased.

曲面凹模拉深与平端面凹模拉深相比，降低了极限拉深系数，减少工序、提高了效率，降低了成本。

When solder bumps (22) on the die are reflowed, the fluxing agent acts to remove any oxides present on the solderable surfaces of the substrate or the die.

当管芯上的焊料突点（22）被回流时，该助焊剂的作用是清除基板或管芯的可焊接表面上存在的任何氧化物。

I glared at him. I may not die now… but I'm going to die sometime.

我瞪着他。我也许不会在现在死去……但我终有一日会死去的。

MARC. And also the influence on final thickness distribution of surface friction of preforming die and forming die was analyzed.

MARC有限元模拟研究了不同形状的预成形模对深筒形件侧壁厚度分布的影响，并分析了预成形模和终成形模的表面摩擦系数分别对成形件壁厚分布的影响，提出了模具型面变摩擦控制厚度分布的方法。

The results show that the friction on the lower die surface is beneficial to the preforming;the clearance between the roller base and lower die obviously influences the base end and open end dime...

结果表明，预成形时下模端面摩擦属有利摩擦；旋轮底面与下模间隙对最终工件的底部及口部尺寸具有较大影响；旋轮沿径向施加给工件的压下量对腰鼓件质量影响较大。

Listen,point and check your answers.

听，指出并且检查你的答案。

Warming needle is one of effective treatment methods for knee arthralgia aggravated by cold,and it is simple,safety,so it should be developed in clinical acupuncture and moxibustion extensively.

但以本院科针灸门诊在2005年1月—2006年6月期间共收治膝痛患者100余例，经过临床的诊断后，其中施以温针治疗的48例，疗效显著，报道如下。1临床资料本组病例48