查询词典 die holder

But sometimes I think if we can put all the centers together like dynamic balance and stripper pressure center of punch holder, vibrate and clamping center of die shoe etc, how perfect it is!

很多时候我在想，如果我能够将所有的中心例如上模的动平衡中心、卸料中心、下模的振动中心、夹钳固定中心等等都放在一条中心线上，那将是一个怎样的境界？

It studied many factors such as blank holder pressure, anti-pressure, clearance between punch and bottom die, and parameters of dentiform on blank holder, analyzed the influence of these factors' change to stress and strain field in distortion area and the appearance of shear crack, summarized the appropriate ratio of blank holder pressure and anti-pressure, and the best range of other factors.

从压边力、反压力、相对冲裁间隙、压边圈齿形参数等各种因素出发，分析了这些因素的变化对于变形区应力应变场与剪切面裂纹产生的关系，并得出了压边力与反压力的合适配合比例，以及其他参数的正确取值范围。

In this study, the simulator was applied to square-cup deep-drawing process, using 36 blank holder modules with 3 embedded hydraulic cylinders, that is, a total of 108 segment blank holding actuators were employed for controlling the material flow of blank into the die cavity.

在这项研究中，这个模拟器是用于制造过程的基础上，利用square-cup 36边模块3嵌入式液压缸，也就是说，共108段压致动器是用来控制物料流进模具型腔的空白。

Increasing the shim thickness increases the gap between the die face and blank holder and allows more metal to flow inward.

增加垫片的厚度也就是增加模具表面和压边圈间的间隙从而容许更多的金属向前流动。

To improve the characteristic of stamping process for lamp holder shell,the operation principle and structural design of multi-position progressive drawing and blanking die for lamp holder shell were described.

针对灯头壳零件的结构特点和生产要求，介绍了灯头壳多工位拉深级进模的结构设计要点和工作原理。

With the exception of severe blank holder deflection, these factors can be corrected by making minor permanent adjustments, such as increasing the blank holder force, re-adjusting the equalizer height, and refitting or spotting the blank holder or the die face.

除了压边圈的严重变形外，这些因素都可以通过最小的永久性调整来矫正，如增加压边力、调整平衡块的高度和重新匹配或研配压边圈或凸/凹模的型面。

With the exception of severe blank holder deflection, these factors can be corrected by making minor permanent adjustments, such as increasing the blank holder force, re-adjusting the equalizer height, and refitting or spotting the blank holder or the die face.

除了压边圈的变形外，这些因素都可以通过最小的永久性调整来矫正，像增加压边力，调整平衡块的高度，重新布置压边圈或凸凹模。

Equalizers are spacer blocks mounted on either the blank holder surface or the die face that maintain a specific gap between the die face and blank holder surface.

平衡块是一些安装在压边圈或凹模型面上用来维持压边圈和凹模间的压边面间隙的垫片。

Equalizers are spacer blocks mounted on either the blank holder surface or the die face that maintain a specific gap between the die face and blank holder surface.

在很多情况下，拉延模设计时不放置平衡块。平衡块是一些安装在压边圈或凹模型面上用来维持压边圈和凹模间的压边面间隙的垫片。

Barlat1989 is recommended owing to its computational effectiveness. The technique is given using the dynamic relaxation method to obtain the steady position of the blank inside die opening line from end of holder forming stage to start of die forming stage.

在板料成形过程的数值模拟研究中，提出了将动力松弛法用于获得压边圈成形结束到凸模成形开始之前凹模开口线内板料的稳定位置，从而消除动力效应的处理技术。

Finally, according to market conditions and market products this article paper analyzes the trends in the development of camera technology, and designs a color night vision camera.

最后根据市场情况和市面上产品的情况分析了摄像机技术的发展趋势，并设计了一款彩色夜视摄像机。

Only person height weeds and the fierce looks stone idles were there.

只有半人深的荒草和龇牙咧嘴的神像。