查询词典 die forming

Type ZZM-10A cutter sharpener is applicable to grind milling cuttrt of all kinds of diameter,shapes and angles for die sinker,also to die pin corres ponding to the miller according to die sinker scale,it has ability of grinding turning tool,drill.So it is a necessary equipment in using die sinker with excellent figuration,new stucture and good application.

ZZM-10A型万能磨刀机，造型美观，结构新颖，使用性能良好，用于刃磨刻模铣床的各种直径、形状及角度的铣刀和按刻模比例与之相适应的靠磨削，因此它是刻模铣床使用中必需的配套设备，并有刃磨车刀、立铣刀、钻头的功能和装置。

As the brittleness of low-k material,the traditional wire bonding parameter often lead to die pad crack or Au-AL matter bad;after used low-k material,die size,die pad opening and die pad pitch change to more little,wire change to lengther and density change to more higher,it\' s new challenge for molding and wire bonding;at the same time, low-k material also require to control the thermal stress in package.

由于低介电常数材料的脆性，传统的引线压焊参数设置将会导致焊盘碎裂以及金铝化合物不良；由于使用低介电常数材料后，芯片尺寸、压焊区域和压焊间距进一步减小，金线压焊长度和密度大大增加，这就为压焊和模塑提出了新的要求；同样由于低介电常数材料的应用，对封装体内部的热应力的控制也提出了更高的要求。

A piece of hot metal sufficient to slightly overfill the die shape is placed in the bottom die, and the top die is forced against it, so that the metal takes the internal shape of the die.

将一块大小足以充填模腔并能稍有溢出的加热金属放入底模，并将顶模加压合拢，这块金属便获得该模腔的形状。

In die model, we can get die price of listed company on the condition of full-flowing by multiplying PE and earning, and then we can get die reasonable flowing-price of stated-owned share baaed on die ihaie-holding structure.

首先，用合理市盈率乘以每股收益得到全流通条件下股票的价值，然后根据股权结构倒推出国有股减持的合理价格。

At present die design, 3D die design is the trend of development. This thesis designed 3D die of blanking and draw processes of taillight supporter with UG software, Summarized the merits and the characteristics of 3D die design.

最后，在现代模具设计里，三维模具是发展趋势，本文结合UG软件对汽车尾灯支架落料和拉延工序的模具进行了三维设计，总结了三维模具设计的优点和特点。

In the standard designing procedure of stamping die , the calculation formulas of dimensions of both punch and die plate are derived based on such a principle that for blanking operation to produce the punch with the die plate as the basic part, and for the punching operation to produce the die plate with the punch as the basic part.

在冲裁模设计中，冲裁模的凸模、凹模刃口尺寸计算公式是根据落料以凹模为基准件配制凸模，冲孔以凸模为基准件配制凹模的原则建立的。

In this dissertation the"Penalty"finite element method was employed to compute the velocity of the three-dimensional flow of power-law fluid in a profile die. In order to decrease the needed computer memory and raise the stability of numerical simulation, a set of decoupled methods such as PFEM, pseudo-body force method and transformation of momentum equation to the elliptic equation was developed to establish the general finite element equations to compute the distributions of velocity and viscoelastic stress of the three-dimensional viscoelastic flow of the Phan ThienTanner fluid in a profile die. During numerical simulation of the extrudate swell of the PTT fluid, the flow in the die and out of the die was analyzed separately, which demands less computer memory.

本文建立了求解挤出口模内幂律流体流动速度场的通用三维罚有限元模型；对于非线性粘弹性的Phan Thien-Tanner流体，为了降低模拟计算对计算机硬件的要求，并使模拟计算更加稳定，采用了一种去耦算法，包括罚有限元方法、拟体力方法和动量方程的椭圆类方程转化方法，并建立了求解速度场和粘弹性应力场的总体有限元方程；对于PTT流体的挤出胀大问题，提出了挤出胀大熔体口模内外分离模拟法，这样可以显著降低数值模拟对计算机硬件的要求。

In this dissertation the"Penalty"finite element method was employed to compute the velocity of the three-dimensional flow of power-law fluid in a profile die. In order to decrease the needed computer memory and raise the stability of numerical simulation, a set of decoupled methods such as PFEM, pseudo-body force method and transformation of momentum equation to the elliptic equation was developed to establish the general finite element equations to compute the distributions of velocity and viscoelastic stress of the three-dimensional viscoelastic flow of the Phan ThienTanner fluid in a profile die. During numerical simulation of the extrudate swell of the PTT fluid, the flow in the die and out of the die was analyzed separately, which demands less computer memory. The key techniques used in numerical simulation of the three-dimensional extrusion from dies such as decision of boundary conditions, creation of initial velocity field, selection of penalty factor, high Weissenberg number problem , regeneration of the free surface were studied in detail.

中文题名聚合物异型材口模挤出三维流动研究副题名外文题名 Study on three-dimensional flow of polymer melts during the process of profile extrusion from dies 论文作者涂志刚导师柳和生包忠诩教授学科专业材料加工工程研究领域\研究方向学位级别博士学位授予单位南昌大学学位授予日期2001 论文页码总数148页关键词挤出成型聚合物材料挤出口模聚合物异型材馆藏号BSLW /2003 /TQ320 /9 本文建立了求解挤出口模内幂律流体流动速度场的通用三维罚有限元模型；对于非线性粘弹性的Phan Thien-Tanner流体，为了降低模拟计算对计算机硬件的要求，并使模拟计算更加稳定，采用了一种去耦算法，包括罚有限元方法、拟体力方法和动量方程的椭圆类方程转化方法，并建立了求解速度场和粘弹性应力场的总体有限元方程；对于PTT流体的挤出胀大问题，提出了挤出胀大熔体口模内外分离模拟法，这样可以显著降低数值模拟对计算机硬件的要求。

We can also provide special purpose of bending die, elbow-, knife-shaped die, 90 °, 60 °, 45 °, 30 °, R-shaped, cylindrical, pressure-bending, U-bending and embossing Die, Die container, various Denggan mode, cutting plate machine blade, to map processing, non-standard design.

我们还可以提供特殊用途的折弯模具，有弯头模、刀形模、90°、60°、45°、30°、R形、圆柱形、折弯压力形、U型和折弯压印模、集装箱专用模、各种灯杆模、剪板机刀片、来图加工、非标设计等。

The main products of the sticks is die-cutting on automatic die-cutting machine requires will rely on a pipe of knife more force several narrow-necked, smooth production after the die cutting machine out, in the sense of narrow-necked reflected in the die-cutting on the box of the edge is not smooth.

影响产品美观的主要原因是在平压平自动模切机上进行模切加工时需要将靠叼口边的刀多敲破几个小口，才能顺利地将模切后的成品从机器中拉出来，敲破的小口体现在模切后的盒上是边缘不光滑。

This time, we do not want to colorize the image. I've dragged my Hue slider to the left to a value of -123

这次不要勾选着色，我将色相的滑标向左移到-123

A timely report from an independent prosecutor would surely be helpful in buttressing and justifying that order.

及时报告从一个独立的检察官一定会有助於支撑和合理的秩序。