查询词典 die for

The load cell on the die holder measures the pulling tension to which the strand is subject for accurate control; this value is displayed and recorded.

为精确控制，模座上的测压元件测量支配裸绞线的拉力，该数值被显示和记录。

The results show that the die radius, blank holder force and friction coefficient are all significant on the forming process.

结果表明，单位压边力、摩擦系数、凹模圆角半径对拉深过程均有显著影响，其中贡献率分别为凹模圆角半径41.04%，摩擦系数30.27%，压边力24.68%。

A three-dimensional finite-element model, which includes plate, punch, die and holder pad, is established to simulate the drawing process based on the characteristics of the square box part.

根据方盒形件的特点，本文建立了包括板料、凸模、凹模以及压边圈在内的三维有限元分析模型。

A quarter model is used to simulate for the reason of symmetry. Punch, die and holder pad are regarded as rigid body because of little deformation.

考虑到对称性，取四分之一模型进行有限元模拟，由于凸模、凹模以及压边圈变形都很小，故将其视为刚体。

Then triaxial elastic finite element model was made through ANSYS software for U-type die holder with numerical simulating analysis and proofread of stress and strain.

在精度要求高时，这种精冲模架可实现一次精密成形，大大降低劳动强度，提高劳动生产率，是一种先进而实用的加工方法。

The draw ratio is the direct relationship between the draw punch and the blank edge—the greater the distance between the draw punch and the blank edge, the greater the resistance to flow, primarily because of the additional surface area of sheet metal clamped between the die face and the blank holder.

拉伸比直接体现在拉延凸模和板料边缘之间的关系--拉延凸模和板料边缘之间的距离越大，限制流动的阻力越大，主要是因为在压边圈和凹模表面间有额外金属板表面被夹紧。

The draw ratio is the direct relationship between the draw punch and the blank edge—the greater the distance between the draw punch and the blank edge, the greater the resistance to flow, primarily because of the additional surface area of sheet metal clamped between the die face and the blank holder.

拉伸率直接体现在拉伸冲头和展开平板边缘之间的关系---拉伸冲头和展开平板边缘之间的距离越大，限制流动的阻力越大，主要是因为在压边圈和模具表面间有额外金属板表面被夹紧。试着用不同尺寸和外形的展开平板进行实验。

With the exception of severe blank holder deflection, these factors can be corrected by making minor permanent adjustments, such as increasing the blank holder force, re-adjusting the equalizer height, and refitting or spotting the blank holder or the die face.

除了压边圈的严重变形外，这些因素都可以通过最小的永久性调整来矫正，如增加压边力、调整平衡块的高度和重新匹配或研配压边圈或凸/凹模的型面。

With the exception of severe blank holder deflection, these factors can be corrected by making minor permanent adjustments, such as increasing the blank holder force, re-adjusting the equalizer height, and refitting or spotting the blank holder or the die face.

除了压边圈的变形外，这些因素都可以通过最小的永久性调整来矫正，像增加压边力，调整平衡块的高度，重新布置压边圈或凸凹模。

After an investigation on the rules of this deep drawing process, a virtual orthogonal experimental design is adopted to determine the significance of processing parameters, die radius, blank holder force and friction coefficient, on the forming process.

同时，采用正交试验分析方法，研究了单位压边力、摩擦系数、凹模圆角半径和凸凹模间隙等工艺参数，对该拉深成形过程的影响规律。

Vishnu entered a dark fourth dimensional dream that did not support his field or continued life.

毗瑟挐进入了一个第四密度的黑暗梦想，那里并不支持他的能量场或继续生命。

Leaders and decision-making persons use it to collect the data, including the information of unit work, handing in fee, oweing fee, prepaying fee,changing and afterpaying and account transfering of joining-insurance employee, and account paying of all kinds of insurances from hospitalization insurance institutions.The collected data is picked up, organized, switched and showed to user.

该子系统主要面向各级领导、决策分析人员；从各个医疗保险经办机构和定点医疗机构采集数据，包括在各个医疗保险经办机构处理的单位办公信息，单位缴费、欠费、预缴费信息，参保职工变更信息，参保职工增减变动信息，参保职工补缴信息，参保职工帐户划拨信息：包括各定点医疗机构处理的各险种帐户支出信息，各险种的统筹金支付信息等；将采集的数据提取，组织和转换，然后展示给用户。