查询词典 die casting

It also provides a new way for casting engineers to study casting foundry Process.

这也为铸造工程师提供新的途径来研究压铸过程。

The results show that the quantity of duplex impurity in CSP thin slab is minute. The size of crystal grain of the steel strip side along the width direction during continuous casting and continuous rolling,cold rolling and annealing is finer than that of the steel strip center and the phenomenon is more obvious duing continuous casting and continuous rolling than during other processes.

结果表明：包钢CSP薄板坯中复合夹杂的数量极少，在CSP连铸连轧及后续的冷轧薄板生产过程中，铸坯、热轧板、冷硬板和退火薄板沿宽向边部的组织均较中部的组织细小，且铸坯和热轧状态下较为明显。

In the fields of metallurgy system, the projects that we supplied assemblies for are as follows: Bao Steel 3rd Project (hot rolling、link casting、wire material、billet ban); Workshop Steel Structure、Bao Steel "Shiwu" Programming Lenience Ban、Blast Furnace、Link Casting; Wu Steel 3rd Steel-making

冶金系统在冶金系统，公司产品占上海市建筑企业五十强排名第一的上海宝冶采购总量超过60%，配套其宝钢三期工程（热轧、连铸、线材、坯板等）厂房钢结构、宝钢十五规划宽厚板、高炉、连铸等重点工程。

The method adopted include mainly intermix in deep layer, high pressure spray casting and pressure casting etc.

多种支护结构型式的综合应用是解决特殊地区基坑工程结构支护的有效办法。

For two continuous casting billets of typical stainless sheets (304 and 0Cr13), three positions including the edge, 1/2 and 1/4 along the thickness were spectroscopically analyzed through successive layer and multiple point modes. The uniformity of lumpish continuous casting billet sample was studied by statistical analysis and the major factors influencing the accuracy of spectral analysis were discussed.

对于304和0Cr13两个典型不锈钢品种的连铸坯，沿厚度方向分别取边缘、1/2、1/4三个不同部位进行逐层、多点光谱分析，并利用统计分析手段，考察了连铸坯块状试样的均匀性，分析了影响钢材成品光谱分析准确度的主要因素。

The main objective of this project is to apply the gel-casting technique, a novel ceramic forming method, in the development of IT-SOFCs. The gel-casting technique was investigated, modified and optimized to synthesize strontium doped lanthanum manganate La_(0.72Sr_(0.18)MnO_3, LSM, lanthanum strontium manganese chromite (La_(0.75)Sr_(0.25)_(1-x)Cr_(0.5Mn_(0.5)O_(3-δ), LSCM, LaCoO_3-based nano powders and lanthanum silicate apatite electrolyte powders.

本论文采用优化的凝胶注模工艺合成了以下粉体：Sr~(2+)离子掺杂的锰酸镧(La_(0.8)Sr_(0.2)_(0.9)MnO_3，LSM阴极粉体、Sr~(2+)和Mn~(2+)离子共掺杂的铬酸镧(La_(0.75)Sr_(0.25)_(1-x)Cr_(0.5Mn_(0.5)O_(3-δ)，LSCM阴极／阳极粉体、LaCoO_3阴极纳米粉体和磷灰石结构硅酸镧La_(10)Si_6O_(27)电解质粉体。

In the third part of the paper, another novel technology, named as Mould Oscillation-less Electromagnetic Continuous Casting under AMMF was proposed in order to replace the huge mechanical mould oscillation system by AMMF imposing outside the mould in continuous casting.

进行了三种波形高频调幅磁场下的无结晶器振动电磁连铸初步实验研究，实验结果表明：在方波、三角波和正弦波调幅磁场作用下的无结晶器振动电磁连铸过程中，当调制波频率略低于系统固有频率时，弯月面与结晶器壁间断接触距离最大。

Study on a Expert System for Analysis of Casting Defect;2. The effect of casting defect such as microporosity and the inclusions in the process of crack initiation,crack propagation and fracture was analyzed.

系统研究了L114A合金疲劳损伤特征，分析疏松、夹杂物等铸造缺陷在疲劳裂纹的形核、裂纹的扩展以及瞬断中所起的作用，表明铸造过程中形成的铸造缺陷数量、尺寸、位置对金属的疲劳性能都有不同程度的影响。

The mechanism of microscopical roughness forming on the aluminiumalloy casting surfaces has been studied by plaster investment casting.

本文通过熔模石膏型铸造法研究了铝合金铸造表面微观粗糙度的形成机理。

A general problem in protecting the casting ingots by using expanded complex mould casting mold powder is the surface defect that slag deposition can be evolved easily in ingots head.

使用膨胀型复合模铸保护渣保护浇注钢锭，普遍存在的一个问题是容易使钢锭产生头部积渣这一表面缺陷。

Listen,point and check your answers.

听，指出并且检查你的答案。

Warming needle is one of effective treatment methods for knee arthralgia aggravated by cold,and it is simple,safety,so it should be developed in clinical acupuncture and moxibustion extensively.

但以本院科针灸门诊在2005年1月—2006年6月期间共收治膝痛患者100余例，经过临床的诊断后，其中施以温针治疗的48例，疗效显著，报道如下。1临床资料本组病例48