查询词典 dentation

In dentation line group, 3,5 years survival rate was 83.6%,74.4% respectively, and the local recurrence rate was 4.8%.

齿状线组：3年、5年生存率为83.6%、74.4%，局部复发率4.8 %；0～2 cm组：3年、5年生存率为84.6%、72.1%，局部复发率7.7 %。

Results the basic CT features of 102 patients with Peripheral lung adenocarcinomas were as follows:vacuole or air bronchogra charging sign was found in which as were seen in 24 cases (80%) in high differential adenocarcinoma and were seen in 10 cases (30.3%) in moderate differential adenocarcinoma but not seen in low differential ones, spiculation sign in 73(71.5%). spiculate protulerance sign in 52 (50.9%). lobulation sign in 79(77.4%), pleural in dentation sign in 65(63.7%), vessel convergenoe sign in 69 cases(67.6%), and calcification inside the lesion was 31 cases. 67 cases had more then three basic CT signs mentioned above.

结果 102例周围型肺腺癌的主要CT分析征象是：空气支气管征或空泡征、高分化腺癌24例（80％）、中分化腺癌10例（30.3％）、低分化腺癌无此征、毛刺征73例、棘突征52例、分叶征79例、胸膜凹陷征65例、血管集束征69例、病灶内钙化31例，其中67例出现上述三种以上征象。

The combination of corundum-coated cBN abrasive with vitrified bond is better than that of Ti-coated or un-coated cBN. And the buffer layer from cBN abrasive, corundum coating to bond is perfect because part of corundum coating melts into vitrified bond to build dentation combination.

表面涂覆刚玉和镀覆Ti的cBN磨粒与结合剂的结合效果均比未镀覆的好，但涂覆刚玉比镀覆Ti的效果更好，刚玉涂层以牙形溶入结合剂中使得磨粒、镀层和结合剂三者过渡良好。

Adoption special three layer structures,adopt the Japanese home nicety to roll the bead bearings inside the layer,is a high strength nylon in the center 66,a PU material,in the center the layer design become inverted barbs dentation.

轮子采用特殊三层结构，内层采用日本进口精密滚珠轴承，中间为高强度尼龙66，外包PU材料，中间层设计成倒钩齿状。

Founded in 1998, Hangzhou ZhongLing Advertising Materials Co., Ltd is specialized in producing ZL3000T/S Continuous High Frequency Plastic Welder,Banner Slitter, Ink Vacuum Cleaner, Auto-Grommet Machine, Folder, Dentation strip and Hot Air Welder and so on.

公司自1998年成立以来，已经研发和生产了ZL3000T/S连续式高频拼接机、分切机、喷绘机专用吸墨器、热风焊接机，自动打扣机、做立体字用冲齿机和折角器等系列化广告专用设备。

1The hangs adoption special three layer structures,adopt the Japanese home nicety to roll the bead bearings inside the layer,is a high strength nylon in the center 66,a PU material,in the center the layer design become inverted barbs dentation.

1轮子采用特殊三层结构，内层采用日本进口精密滚珠轴承，中间为高强度尼龙66，外包 PU 材料，中间层设计成倒钩齿状。

40KG . The super mute hangs a product characteristics:1 The super mute hangs an adoption special three layer structures, adopt the Japanese home nicety to roll the bead bearings inside the layer, is a high strength nylon in the center 66, a PU material, in the center the layer design become inverted barbs dentation.

超静音吊轮产品特点：1 超静音吊轮采用特殊三层结构，内层采用日本进口精密滚珠轴承，中间为高强度尼龙66，外包 PU 材料，中间层设计成倒钩齿状。

This paper studies the main geometrical parameter such as angle, height, width, stagger and the upper width in dentation and trapezoid flow path, firstly, uses the single-phase numerical simulation of the computational fluid dynamics technique to analyse the influence of different geometrical parameter on discharge coefficient and flow state exponent of drip emitter. Secondly, uses the two-phases numerical simulation of CFD (1% sand content ) to analyse the influence of the above mentioned geometrical parameter on the contribution regulation of sand and anti-clogging performance. Thirdly, uses the PIV （ particle Tracking Velocimetry ） technique which can see the small-scale flow path to observe and test the trajectories and velocities of solid particles in labyrinth flow path, and analyses the basic factors which can influence the movement characteristic of solid particles and the flow state in flow path.

本文以齿形流道、梯形流道为主要研究对象，以流道转角、流道高，流道宽、偏差量及梯形流道上底宽为主要结构参数，首先应用 CFD 单相流数值模拟技术对不同结构参数灌水器流道水力性能进行模拟，分析了不同结构参数对流态指数和流量系数的影响，其次，应用 CFD 两相流（含沙量为1%）数值模拟技术分析了结构参数对含沙量分布规律和抗堵塞性能的影响，然后，应用 PIV 可视化测试方法测试了固体颗粒在流道内运行轨迹及速度，分析了影响固体颗粒运动特性及流道内流体流态的基本因素，最后，对上述流道结构形式通过模具加工及滴灌带试制，进行了标准化测试（ GB/T 17187-1997 农业灌溉设备滴头技术规范和试验方法与 ISO 标准 ISO /TC23 /SC18 /WG5N4短周期堵塞测试程序），测试结果验证了 CFD 模拟结果，并提出了迷宫结构流道灌水器的抗堵塞设计方法。

In the negative and interrogative forms, of course, this is identical to the non-emphatic forms.

。但是，在否定句或疑问句里，这种带有"do"的方法表达的效果却没有什么强调的意思。

Go down on one's knees;kneel down

屈膝跪下。。。下跪祈祷