查询词典 delivering gear

That the curves of the normal force and friction force between two corresponding gear teeth in a given condition can supervise the design and optimization of gear system.

得到了某一特定传动条件下单对齿轮轮齿法向力及齿间摩擦力的变化规律曲线，从而可以指导齿轮系统的设计和优化。

Based on the measurement of noise of an idling lathe C630,the effects of gear tooth friction on change gear noise ,and the relation between friction excitation frequency and gearing frequency were analyzed.

结果证明：齿面摩擦对齿轮振动的激励频率是啮合频率的2倍，可以利用适当的润滑有效地抑制齿轮噪声的高频成分。

This is because the angle on the worm is so shallow that when the gear tries to spin it, the friction between the gear and the worm holds the worm in place.

这是因为，蜗轮蜗杆的升程角很小，当涡轮要带动蜗杆时，蜗轮蜗杆间的摩擦力把蜗杆锁住了。

The working principle of spring friction draft gear for heavy haul freight cars was introduced,and a virtual prototype model of spring friction draft gear was established based on the ADAMS software.

介绍了重载货车弹簧摩擦式缓冲器的工作原理，采用ADAMS多体动力学仿真软件搭建了弹簧摩擦式缓冲器的虚拟样机模型。

Based on the measurement of noise of an idling lathe C630,the effects of gear tooth friction on change gear noise,and the relation between friction excitation frequency and gearing frequency were analyzed.

以一台C630车床空转噪声的测试数据为依据，分析了齿面摩擦对车床挂轮噪声的影响，以及摩擦激励频率与齿轮啮合频率的关系，并通过涂油润滑降低挂轮噪声的实验对此进行了验证。

However, the influence both ship hull deformation and friction between gear teeth are omitted in strength calculation of gear driving fixed in boat in traditional design.

算例表明，船体变形及齿间摩擦时齿轮强度的影响的确不可忽视。

Involute gear ; friction coefficient between teeth ; tooth number ; driven gear ; output torque ; fluctuation ratio

渐开线齿轮；齿间摩擦系数；齿数；从动轮；输出扭矩；波动率

The main identifying characters of wear particle on the ferrogram such as dimension,distribution,quality,component and form of the wear particle were generalized for the three friction couples of gear case including gear,bearing and sliding contact which is in the different phases of running-in wear,normal wear and abnormal wear and in the different degrees of overload,over-speed and fatigue.

介绍了铁谱分析的原理、样品的制备方法和铁谱分析的步骤，概括了齿轮箱齿轮、滚动轴承、滑动接触3种主要摩擦副在磨合磨损、正常磨损、异常磨损3个阶段的磨粒的主要识别特征，包括尺寸、尺寸分布、数量、成分和形貌等。

The equation and the mathematical model are acquired just after studying of the theory of gearing, and the mathematical model also result from the actual manufacturing method. Then, the paper accomplish the accurately 3D-modeling of the four generally used types of gears: cylindrical spur gean cylindrical helical gean straight bevel gear and curved-tooth bevel gear.

利用具有强大三维造型功能的工程软件实现了四种常见齿轮：圆柱直齿轮、圆柱斜齿轮、直齿锥齿轮和弧齿锥齿轮的三维造型，解决了齿轮的精确三维建模难题。

The vibration of gear case is further calculated with the excitation oweing to the fluctuation of gear load.

以齿面动载作为激励，本文进一步研究了齿轮箱壳的振动响应。

Methods Clinical data of 3 cases of bile duct injury during laparoscopic cholecystectomy were analyzed retrospectively.

回顾总结3例LC术中胆管损伤的临床资料，分析3例胆管损伤的原因及对策。

These techniques are applied to the gobang.

本文将这些技术用于五子棋中。