查询词典 deforming

In order to settle the difficult problem of deforming and cracking of a shaft furnace's ridge under high-temperature conditions,reform measures were put forward on the basis of an analysis of causes of deforming and cracking of the ridge .

为解决竖炉脊顶高温工矿条件下变形开裂的难题，在对脊顶变形开裂原因进行分析的基础上，提出了改造措施。

By research on developing and utilizing of analcite muddy rock resources in Ningxia,the technique of using analcite to decline fluoride water including purifying,deforming,and modeling,this paper mainly studied removing rate and adsorbing capacity of fluorine ion in high fluoride water .

为了探讨开发利用宁夏境内含有方沸石矿物的泥质岩石资源，通过提纯、变性、造型等技术手段和工艺研制了方沸石矿物降氟改水新材料，并对高氟水中F-的去除率和吸附容量进行了研究。

The backspin as we discussed before generates the lift by deforming the airflow around the ball.

下旋，我们讨论过的升降机的产生变形的球周围的气流。

Benda chooses high grade materials to further improve products in pressure,precision and finish based on world traditional manufacture,to effectively prevent products from deforming,shrinking and leakage.

奔达选用优质材料在世界传统制造基础上，进一步提高产品的压力、精密度、光洁度。

In this dissertation, the deforming process of Continuous Extrusion Cladding has been systematically studied by both theoretical a...

本文首次对连续挤压包覆成形过程进行了系统的理论和实验研究，主要内容包括： 1。

The results show that the flow stress decreases with increasing deforming temperature and increases with increasing strain rate. The flow stress of the alloy during hot compression deformation can be described by constitutive equation in hyperbolic sine function with a hot deformation activation energy of 196.27 kJ/mol. Partial recystallization takes place in the alloys deformed at a high temperature or at a low strain rate, and large number of dislocations and subgrains are observed in the alloy. The elongated grains observed in the samples coarsen with increasing temperature and decreasing strain rate. Correspondingly, the subgrain size increases and the dislocation density decreases. The main soften mechanism of the alloy transforms from dynamic recovery to dynamic recrystallization.

结果表明：Al-Cu-Mg-Ag耐热铝合金在热压缩变形中的流变应力随着温度的升高而减小，随着应变速率的增大而增大；该合金的热压缩变形流变应力行为可用双曲正弦形式的本构方程来描述，其变形激活能为196.27kJ/mol；在变形温度较高或应变速率较低的合金中发生部分再结晶，并且在合金组织中存在大量的位错和亚晶；随着温度的升高和应变速率的降低，合金中拉长的晶粒发生粗化，亚晶尺寸增大，位错密度减小，合金的主要软化机制逐步由动态回复转变为动态再结晶。

With the result of analyzing the Greedy Algorithm, an local area encrgy term is defined and added to the target function for capturing the image feature in a wider region and guiding the deforming curve into the concave regions.

传统的参数活动轮廓模型分割图像时，要求初始轮廓线设置在感兴趣区域的边界附近，曲线在变形过程中难以分割深度凹陷区域。

Background: The development of lipomatosis over the extremities can be distracting to affected individuals because of their deforming conspicuousness, this being especially the case for those where such lesions occur over the denuded upper extremities.

背景：罹患肢体多发性脂肪瘤的病患很在意因为脂肪过多而导致外形上的明显畸形，尤其当这些脂肪长在病患裸露的上肢上会更明显。

Our approach consists of the following steps: providing a sketch based mapping between the sources and the target; deforming the target based on the deformations of the corresponding sources by means of differential mean value coordinates; smoothing the deformed target with constrained minimization method to form a key frame of the target animation; and interpolating between key frames created from to produce a complete 3D animation of the target.

该框架由以下几个步骤组成：使用草图在源网格和目标网格间建立映射；使用非闭合网格均值坐标，根据源动画的运动风格来变形目标网格；对变形后的目标网格求解最小化约束函数以获取光滑的目标网格，从而生成目标动画的关键帧；对由产生的结果进行插值，产生完整的目标对象的三维动画。

Through calculation and analysis of static modal under dead load, live load and water load, we derived the non-seismic internal force and deforming of the structure.

通过对静力模型在恒载、活载和水荷载作用下的计算和组合，得到了结构非抗震设计的内力和变形。

Liapunov—Schmidt method is one of the most important method in the bifurcation theory.

Liapunov—Schmidt方法是分叉理论的最重要方法之一。

Be courteous -- even when people are most discourteous to you .

要有礼貌──即使当別人对你最不礼貌的时候。