查询词典 deformed

The first holding members are disposed on the opposite sides of the first blade, respectively .Each of the first holding members has a cushioning property by which each of holding members is elastically deformed to press the sheet-shaped material during cutting operation.

首次举行的成员被弃置于对面两岸的第一刀片，分别为每首控股成员有一个缓冲的财产，其中的每个成员是控股弹性变形，按资产负债表形的材料在切割操作。

Each of the first holding members has a cushioning property by which each of the first holding members is elastically deformed to press the sheet-shaped material during cutting operation.

每一个第一个把持成员藉着成员有柔性不成形压张哪一个每一个第一个把持有缓冲剂特性-在锐利的操作期间作形了材料。

Based on geology mining condition of Xinfa Mine,according to probability integral method,the de- gree of surface movement deformed is predicted,and the influence to the buildingson the surface is analyzed in mine.

依据鑫发煤矿的地质采矿条件，按照概率积分法、矿山开采对地表所造成的移动变形进行了预计，对地表建筑物、评价区内生态环境所造成的影响进行评价分析，提出了矿山开采后所采取的相应措施。

The paper puts forth that the numerical model of actual forming part is reconstructed by RE and the surface is regarded as actual trimmed surface, then grids and nodes mapping relationship between design model and actual forming part is acquired through compelling deformation simulation, and the design trimming line is dispersed into points according to a certain precision and the projective points and the coordinate values of the intersection points of projective line on the grids formed by discrete points are calculated along trimming direction, the new coordinate values of projective points and intersection points of projective line after deformation are calculated based on the mapping relationship of grids and nodes, the deformed trimming line can be acquired through fitting the points into curve.

本文提出通过逆向工程技术重构出实际冲压件的型面并以此型面为修边后实际冲压件的型面，然后采用强制变形仿真的方法建立设计模型和实际冲压件重构模型的网格和节点映射关系。将设计修边线按一定精度离散成点，然后根据修边方向计算出各点在网格上形成的投影点和投影线交点，根据之前计算出来的网格和节点映射关系就可以计算出投影点和投影线交点在变形后的新坐标，将其拟合成曲线就可以得到变形后修边线的形状。

The lattice was deformed as a particle system using advanced numerical methods, and the hairs were animated using quadratic B-Spline interpolation.

晶格被作为一个粒子系统采用数学方法变形，毛发采用2次B样条插值方法绘制。

Fig.7shows the comparison of radius of curvature and cross-sectional deformed shape between the experiment and FE simulation.

图7所示为曲率半径和横截面形状在试验和有限元模拟中的比较。

The experimental results show that recrystallization of deformed ferrite is strongly influenced by heating rate and occurs mainly between 600℃ and 720℃.

实验表明，在连续退火初期的加热过程中，在600~720℃大量进行再结晶。

When the austenite was deformed in the recrystallization region, sufficient deformation per pass brought about fully recrystallization, and refined the grain.

结果表明奥氏体再结晶区变形时，单道次变形量越大则再结晶进行得越充分，再结晶后的晶粒就越细。

In Chapter IV and Chapter V, we study a deformed t-J model by use of bosonization and renormalization group methods.

文献[1]的作者用玻色化方法和重整化群技术讨论了上述模型在形变参数和J都很小的时候的基本性质。

In this Dissertation, we will study the ground state phase diagram of a one-dimensional deformed t-J model by the bosonization and renormalization group method.

文中，我们用玻色化方法和重整化群技术讨论了形变t－J模型的基态相图。

The work of this paper is as follows: 1. Looking back the progressing history of the linear motor, introducing the features of the elevator driven by linear induction motor, radicating the topic of this paper "the digital frequency variable control of the elevator bi-side direct driven by linear induction motor". The research of this paper covers the conventional VVVF control, space vector based VVVF control, vector control and DTC.

本文主要开展了以下几个方面的工作： 1 回顾了直线电机发展历史，电机的驱动技术演变，特别是针对直线电机的驱动，简要介绍了直线感应电机驱动电梯的优点和不同结构类型，对传统的v／f控制，基于空间矢量法的v／f控制，矢量控制，和基于电压空间矢量的直接转矩控制进行了比较，确立了本课题的研究主题：直线感应电机双边直推式驱动电梯的全数字变频控制。

The article combines with the treatment of a superficial civil air defense work to introduce how the grouting method to improve the performance of the backfill soil.

文章从治理漂浮人防工事的角度提出了注浆技术在改善回填土性质方面的应用，并详细阐述了注浆技术的施工流程。