查询词典 deformation curve

The curve deformation with constant arc length constraint discussed in section one is a frequently encounted problem in the practice of computer animation.

第一节提出的基于弧长不变的曲线变形是动画制作实践中常常遇到的问题。

Five main phenomena were found, firstly, the high plasticity clay could well suitable to large deformation, and had strain-hardening behavior obviously, as well as, the little dilatancy; secondly, there was no correlation between stress paths and shear strength but the stress-strain relations were influenced by stress paths; thirdly, the little stress increment ratio, the higher increase speeding of shear stress and breaking strength under the condition of same initial normal stress; the fourth, the relations between normal strain and normal stress in simple shear test was consistent with which in the single-direction compression test, if there was no dilatancy; the last, the curve of relation between stress ratio and shear strain could be well simulated by hyperbola.

试验结果表明，高塑性粘土能够较好地适应大变形，接触面剪应力与切向应变关系呈剪切硬化型曲线，法向剪胀不明显；接触面剪切强度与应力路径无关，应力应变关系与应力路径密切相关；初始法向应力一定，应力增量比越小，剪应力增长越快，对应的破坏剪应力也越高；无剪胀发生情况下，法向应变与法向应力关系曲线与单向压缩试验具有一致性；应力比与切向应变呈良好的双曲线关系。

Seeing that many researchers devoted themselves to the study of catenary method in recent years. Based on the standard curve of the catenary, the catenary algorithm of two-end-fixed cableway was studied in this paper, which established state coordinate equation and which used the numerical value method to analyze non-linear equations under the condition offeree equilibrium and condition of deformation compatibility.

为此，近年来不少学者致力于单跨架空索道悬链线理论的研究，本文在此基础上，从索道悬链线的标准线形出发，通过建立状态协调方程，来研究架空索道的悬链线精确算法，计算上采用满足力平衡和变形相容条件为基础的数值分析方法来求解非线性方程组。

A curve coordinate system which is suitable for variable height curved box-girder were established. The flexure, torsion and distortional warping displacement functions were established, and the strain-deformation equations were obtained, a spatial finite element analysis method of trapeziform cross section variable-curvature box-girder with vertical symmetrical axis was also presented.

建立适合于变高度曲线箱梁的曲线坐标系，推导了变曲率、变高度箱梁弯曲、翘曲扭转和畸变的位移方程和应变-位移关系式，提出了具有一个竖直对称轴的变高度变曲率曲线箱梁的薄壁曲梁空间分析有限元方法。

Longitudinal distribution pattern of metal lateral displacement in the deformation zone is reconstructed to be quartic plus cubic curve.

关于冷轧窄带和宽带的前张应力横向分布的计算结果与实验结果吻合较好，证明了理论模型是实用可靠的。

The elastic modulus of an object is defined as the slope of its stress-strain curve in the elastic deformation region

一物体的弹性模量被定义为在弹性变形区它的应力－应变曲线的斜率

The resonant points of frequency response curve at different frequency represent different information of winding deformation.

由于不同频率段反映的变形信息不同，因此将频率段按照谐振点个数平均划分为三个区段。

The results indicate that its dynamic stress-strain curve is hyperbolic type. The dynamic strain of LCES decreases with increasing confining pressure, cement content, curing ages and cyclic loading frequency when it is subjected to the same dynamic stress. At the same dynamic strain, the dynamic secant elastic modulus E_(sec of LCES increases and the damping ratio decreases with increasing confining pressure, cement content, curing ages and cyclic loading frequency. The curves ofσ_d～ε_d,E_～ε_d and D～ε_d with different EPS content intersect respectively, the trend of LCES deformation characteristic is inversely proportional to EPS content near the intersection. The value of dynamic strain at the intersection is about 0.5%~3.0%, the magnitude of which is related to the mixing proportions and confining pressure.

试验结果表明，LCES的动应力应变骨干曲线形态符合双曲线；在相同的动应力作用下，LCES产生的动应变随着固结压力、水泥掺量、试样养护龄期和振动频率的增大而减小；在动应变相同的情况下，随着固结压力、水泥掺量、试样养护龄期和振动频率的增大，LCES的动模量增大而阻尼比减小；随着加载次数的增大，LCES的动模量在开始阶段显著降低，然后趋于稳定，但当加载次数达到几百次时，动模量又有增大的趋势；不同EPS掺入比的LCES的动应力应变骨干曲线、动模量随应变变化曲线和阻尼比随应变变化曲线都发生了相交，交点前后EPS掺入比的大小对LCES动力变形特性的影响趋势是截然相反的，交点处的动应变值一般在0.5％～3.0％范围内变化，其大小与LCES的配比以及固结压力有关。

For example, we study the properties of the"centroid curve" and the"auxiliary curve", and identify two planes in which these two curves are defined respectively; we also use the idea of homotopy method to prove a fact that the orbit of a differential system has no triple contact point with the line we considered. Another key technique, which we use several times, is deformation argument.

例如研究由Abel积分之比定义的"质心曲线"和"辅助曲线"的几何性质，并把这两条在不同平面上定义的曲线放在同一坐标系中考虑；利用拓扑中同伦的思想来证明微分系统的轨线不可能与某条直线三重相切；利用几何方法与分析计算相结合证明了某一曲线是正则的；以及连续变动参数的技巧。

Based on the previous results, the method to derive creep constructive model from the indoor experiment data is studied, and these study works are also finished: the reasonable method to determine instance elasto-plastic deformation according to experiment curve, the optimization method to perform curve fitting based on experiment data, the universal method to derive creep constructive model from experiment results.

4在已有研究成果的基础上，对从室内试验数据成果导出流变本构模型的方法进行探讨，研究从室内流变试验曲线上确定瞬时弹塑性变形的合理方法，以及对流变试验数据进行曲线拟合的最优化方法，探讨由室内试验数据成果导出流变本构模型的一般性方法。

They weren't aggressive, but I yelled and threw a rock in their direction to get them off the trail and away from me, just in case.

他们没有侵略性，但我大喊，并在他们的方向扔石头让他们过的线索，远离我，以防万一。

In slot 2 in your bag put wrapping paper, quantity does not matter in this case.

在你的书包里槽2把包装纸、数量无关紧要。