查询词典 deflection

Test results are displayed as a percentage of scale deflection from zero to 100 for any given scale employed.

而测试结果用从0到100偏差的百分比来显示。

The relationship between the maximum buckling deflection of oxide scale and the compressive stress of oxide scale was determined.

依据双材料模型分析高温合金氧化膜的应力状态，确定了氧化膜弯曲剥落的最大挠度与氧化膜压应力间关系。

The rig and debris tray shall be mounted of a weighing balance with a remote readout having a full – scale deflection of at least 0 to 20 kg to an accuracy of 2 g.

夹具和碎屑托盘应该安装在一个带有遥距读数计的称量天平上，天平的满刻度偏转度至少为0到20千克，精确度为2克。

The result shows that the real accuracy of VLBI and GPS geocentric coordinates is within 1cm, and the scale deflection of VLBI and GPS techniques is very little, the result using seven-parameter model to process coordinate transformation is better.

分别采用七参数和九参数模型对VLBI数据和GPS数据进行坐标转换，结果表明，VLBI与GPS的符合精度小于1dm，两种技术所获得的坐标在尺度上的差异很小，七参数的转换结果更优。

If the meter is switched to 20 V DC, for example, then 20 V is the maximum voltage which can be measured, This is sometimes called 20 V fsd, where fsd is short for full scale deflection.

例如，如果仪表切换到DC 20V档，那个20V就是此档可以测量的最大测量电压，这可以称为20V FSD，FSD为满量程值的缩写。

FSD? Full Scale Deflection?

满度偏转，满刻度偏差

By analyzing the load-deflection curve,deformation behavior of two kinds of porosity sandwich panels was discussed.

对载荷-位移曲线进行分析，讨论两种不同孔隙率的三明治板的变形行为，结果表明二者明显不同。

With the exception of severe blank holder deflection, these factors can be corrected by making minor permanent adjustments, such as increasing the blank holder force, re-adjusting the equalizer height, and refitting or spotting the blank holder or the die face.

除了压边圈的严重变形外，这些因素都可以通过最小的永久性调整来矫正，如增加压边力、调整平衡块的高度和重新匹配或研配压边圈或凸/凹模的型面。

With the exception of severe blank holder deflection, these factors can be corrected by making minor permanent adjustments, such as increasing the blank holder force, re-adjusting the equalizer height, and refitting or spotting the blank holder or the die face.

除了压边圈的变形外，这些因素都可以通过最小的永久性调整来矫正，像增加压边力，调整平衡块的高度，重新布置压边圈或凸凹模。

If the blank is wrinkling on the blank holder surface, the cause is most likely one of four factors: insufficient blank holder force; a poor fit between the die face and blank holder surface; an equalizer block that is holding the die face apart from the blank holder surface; or severe blank holder deflection.

如果板料在压边面上起皱，绝大多数起因是后面四个因素之一：不充分的压边力；凹模和压边圈表面不良的匹配；凹模和压边圈间的平衡块；或者是压边圈的严重变形。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐