查询词典 deflection

The principle of work is: When ambient temperature rises, the pressure of the SF6 gas increases, drives the indicator along the clockwise rotation, but at the same time, the mouth of the bimetal compensation system "the U shape" publicizes, then impels the indicator to the counter clockwise rotation, when two kind of strength be equilibrium, the ambient temperature change cannot made the indicator deflection.

工作原理是：当环境温度上升时，虽然容器内SF6气体的密度未发生变化但其压力增大，带动指针顺时方向转动，而当温度上升时，双金属补偿装置的"U形"口张大，则推动指针向逆时针方向转动，当两种运动引起表针的偏转量相抵销时，无论环境温度如何变化，指针都不会发生偏转。

Further on calculating support maximum counterforce and maximum deflection of pipe deformation.

在此基础上计算出支架最大反作用力和管道变形的最大挠度。

It was found that, when a fighter approached on a 'curve of pursuit'(a turning attack, keeping his guns aligned on the bomber), it was very difficult to make a correct allowance for deflection.

当敌机以'追击曲线'（旋转攻击，保持炮口指向轰炸机）的时候，很难作出一个正确的提前量。

The impression cylinder of J2108 offset press is regarded as research object in paper,and the deflection of cylinder is researched as simply supported beam with variable cross section .

以J2108型胶印机压印滚筒为研究对象，将滚筒挠曲变形作为变截面简支梁问题来研究，考虑重力载荷影响，通过积分法得到滚筒在印刷压力和重力载荷作用下的挠曲变形方程和曲线，应用MATLAB7.0平台上编写了印刷滚筒挠曲变形计算程序，为滚筒结构的合理设计提供了依据。

This paper studies on the impression cylinder of J2108 offset press. With finite element method, deflection character of cylinder is achieved in static and dynamic load. Active-compensation to improve flexing-change of cylinder is bring forward, and its compensation character is simulated.

本文以J2108型胶印机压印滚筒为研究对象，通过有限元分析获得滚筒动静态挠曲特性，提出用主动补偿方法改善滚筒挠曲变形，并仿真分析了补偿特性。

Analysed existing dactylogram to collect detailed rules, commutation, dry to valid area, gray scale the respect such as deflection of wet, position undertook be discussinged deep to the influence of dactylogram picture quality, the is based on brim detail to nod information dactylogram picture quality that offers a kind to improve evaluates a method, the dactylogram image to be being collected undertakes quality is evaluated, the pretreatment that is image provides the dactylogram picture with higher quality.

分析了现有的指纹采集细则，对有效面积、灰度变换、干湿、位置偏移等方面对指纹图像质量的影响进行了深入的探索，并提出一种改进的基于边缘细节点信息的指纹图像质量评估方法，对采集到的指纹图像进行质量评测，为图像的预处理提供质量较高的指纹图像。

Radioactive decay studies have found a kinds of elements can be α or β decay and the decay into another element, while the α-decay product of -α-rays became one of the deep structure of the material means of .1911, the Rutherford and others bombarded atoms with α-rays observed wide-angle deflection to determine the nuclear structure of atoms and nuclei was first proposed the term .1919 year, Rutherford and others have also found that with α-ray bombardment of nitrogen will release the nuclear protons, this is the first time Artificial realization of a nuclear reaction, after the bombardment of nuclei with the radiation caused by nuclear reaction method to become the primary means of research in nuclear.

放射性衰变研究发现了一种元素可以通过α衰变或β衰变而变成另外一种元素，而α衰变的产物——α射线又成了人们探讨物质深层结构的手段。1911年，卢瑟福等人用α射线轰击原子、观察到大角度偏折，从而确定了原子的有核结构，并首次提出原子核这一名词。1919年，卢瑟福等人又发现用α射线轰击氮核会放出质子，这是首次用人工实现的核反应，以后用射线轰击原子核来引起核反应的方法逐渐成为研究原子核的主要手段。

The problem is simplified in this paper to the collision of a flexible ball and an elastic plate with large deflection.

把此问题简化为柔性球体与大挠度弹性板的大变形撞击响应问题，采用有限元方法分析了头部与汽车发动机罩撞击的动态响应特性，得出了相关因素对撞击响应的影响特点，并提出了具有行人保护作用的发动机罩的设计原则。

Then compute the bend deflection equation of the plate which has the effect of initial curvature.

第一章简述了工程背景，两种边界情况下板的稳定性问题的临界应力，具有小初始曲率的板的弯曲挠度方程。

For a flat plate the maximum deflection shall be limited to one half of the plate thickness and 1/400 of the unsupported length for a beam.

对于扁板的最大挠度应限制在板厚的一半，对于梁的最大挠度应限制在未支撑长度的1/400。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐