查询词典 cylinders

Once the cylinders were cast in metal the sprues were trimmed off and the part was ready for machining.

一旦气罐投在金属注口被削减小康和部分已经做好准备，加工。

The comparisons of the results have been made between infrared and visible light as well as between hexagonal cylinders and equivalent spheroids and spheres.

自然云中的冷云常包含有冰晶，特别是卷云更是由大量冰晶构成，这些冰晶的尺度从几微米到几百微米，其形态可为各种各样，但最基本和最常见的冰

So ,the temperature is quite essential for an engine to produce power .No engines can work well without suitable operating temperatures .If the engine runs too hot ,it may suffer form pre-ignition,while the air-fuel change is ignited prematurely from excessive combustion chamber temperature.Viscosity of the oil circulating in an over heating engine is reduced.Hot oil also forms varnish and carbon deposits may be drawn into the combustion chamber where it increases HC emission.This also causes poor performance and premature wear ,and may even result in engine damage.What is more,the behavior of the metals at excessively high temperature also differs from that at normal temperatures and can produce a condition in which the metal deforms slowly and continuously at a constant stress,If the engine runs too cold, the fuel will not vaporize properly.If liquid fuel reachees the cylinders,it will reduce lubrication by washing the oil from the cylinder walls and diluting the engin oil.This causes a loss ofperformance, an inrease in HC emissions, and premature engine wear.

所以，温度是很有必要的引擎来产生电力，没有引擎，可以工作，如果没有合适的操作温度，如果发动机运行太热，它可能遭受的形式预点火，而空气燃料的改变是点火过早过量燃烧室temperature.viscosity的石油流通的过度加热发动机是reduced.hot油价也构成了清漆和碳存款可能会被拖入燃烧室而增加hc的emission.this也造成业绩不佳和过早磨损，甚至可能导致发动机damage.what更重要的是，行为的研究金属在过高的温度也有不同，在正常温度下，可以达到的一个条件，其中金属变形速度缓慢，不断在恒应力，如果发动机运行太冷了，燃料价格将不会汽化properly.if液体燃料reachees气瓶，将减少润滑洗油从气缸壁和稀释器oil.this造成损失ofperformance ， inrease在hc排放，发动机过早磨损。

According to the UPV of the SSD condition concrete cylinders, the UPV reduction can reach 7.5% under oven-dry condition, and reach 4.5% under room-dry condition. It is also found that the UPV reduction decreases with decreasing the water-cement ratio of concrete.

圆柱试体(Φ10×20 cm)含水量试验结果显示含水量的改变确实对UPV有所影响，相对於试体面乾内饱和状态，在烘乾状态下之UPV折减达7.5%，而於自然曝晒状态可达4.5%，且随著水灰比的降低此折减百分比亦随之降低。

In 1817, in the side-alleys of this same Champ de Mars, two great cylinders of wood might have been seen lying in the rain, rotting amid the grass, painted blue, with traces of eagles and bees, from which the gilding was falling

在一八一七年，就在那马尔斯广场旁边的小路上，发现了几根蓝漆大木柱倒在雨水和乱草里腐烂，柱上的金鹰和金蜂都褪了色，只剩下一点痕迹。

In 1817, in the side- alley s of this same Champ de Mars, two great cylinders of wood might have been seen lying in the rain, rotting amid the grass, painted blue, with traces of eagles and bees, from which the gilding was falling

在一八一七年，就在那马尔斯广场旁边的小路上，发现了几根蓝漆大木柱倒在雨水和乱草里腐烂，柱上的金鹰和金蜂都褪了色，只剩下一点痕迹。

In 1817, in the side-alleys of this same Champ de Mars, two great cylinders of wood might have been seen lying in the rain, rotting amid the grass, painted blue, with traces of eagles and bees, from which the gild ing was falling

在一八一七年，就在那马尔斯广场旁边的小路上，发现了几根蓝漆大木柱倒在雨水和乱草里腐烂，柱上的金鹰和金蜂都褪了色，只剩下一点痕迹。

Auxiliary Equipment Dryers, Grinders, Metering and Feeding Devices, Heaters, Mold Releasers, Mold Temperature Controllers and Coolers, Sensors, Monitors, Screws and Cylinders, Recycling Equipment and Systems, Testing Equipment and Instruments, CAD/CAM systems, etc.

辅助设备干燥机，研磨机，计量喂料装置，加热器，模具装卸，模温控制器及冷水机，传感器，监控仪器，螺杆机筒，回收设备及系统，检测设备及仪表，CAD/CAM系统等等。

Auxiliary EquipmentDryers, Grinders, Metering and Feeding Devices, Heaters, Mold Releasers, Mold Temperature Controllers and Coolers, Sensors, Monitors, Screws and Cylinders, Recycling Equipment and Systems, Testing Equipment and Instruments, CAD/CAM systems, etc.

辅助设备干燥机，研磨机，计量喂料装置，加热器，模具装卸，模温控制器及冷水机，传感器，监控仪器，螺杆机筒，回收设备及系统，检测设备及仪表，CAD/CAM系统等等。

Auxiliary EquipmentDryers, Grinders, Metering and Feeding Devices, Heaters, Mold Releasers, Mold Temperature Controllers and Coolers, Sensors, Monitors, Screws and Cylinders, Recycling Equipment and Systems, Testing Equipment and Instruments, CAD/CAM systems, etc.

干燥机，研磨机，计量喂料装置，加热器，模具装卸，模温控制器及冷水机，传感器，监控仪器，螺杆机筒，回收设备及系统，检测设备及仪表，CAD/CAM系统等等。

In the negative and interrogative forms, of course, this is identical to the non-emphatic forms.

。但是，在否定句或疑问句里，这种带有"do"的方法表达的效果却没有什么强调的意思。

Go down on one's knees;kneel down

屈膝跪下。。。下跪祈祷