查询词典 cylinder

Analysis of the main reasons is because of fatigue caused by factors such as the copper support ring was broken and the piston rod in the hydraulic cylinder telescopic frequently, the fracture茬口constantly scraping the inner wall hydraulic cylinder mill will pick缸壁, resulting in injury China, so that the speed of decline in hydraulic cylinder; job with the passage of time, strain and缸壁sealing ring, wear ring injuries are increasing, with China to increase the volume, and finally resulted in a serious decline in the speed of hydraulic cylinders.

分析主要原因是，由于疲劳等因素造成的铜质支撑环断裂，在液压缸活塞杆的频繁伸缩中，断裂茬口不断刮磨液压缸内壁，将缸壁拉毛、拉伤而导致内泄，使液压缸速度下降；随着工作时间的推移，缸壁拉伤和密封环、耐磨环的损伤都不断加重，内泄量加大，最后造成液压缸速度严重下降。

Thus, the rigidity of the top deck of the cylinder block is improved, and the sealing between the cylinder block and a cylinder head via a head gasket is improved.

这样，汽缸座的顶板的刚性被提高，并且汽缸座和汽缸盖之间的密封通过一个汽缸盖垫被提高。

When embossing district zhaiyanzhen rubberand drum RADIUS plus the paper thickness is greater than the radius of embossing drum cylinder, paper margin rubber drum circle distance greater than the RADIUS for the imprint of the rollers, paper for the cylinder body relative to the surface of the cylinder of nano-imprint lithography drum slide forward, imprinted deformation and dot gain no significant adverse effects.

当不抬印区某处的橡皮滚筒半径加上纸薄不小于不抬印滚筒筒体半径时，纸张背背距橡皮滚筒圆心的间隔不小于不抬印滚筒筒体半径，纸张背背不绝不差于不抬印滚筒筒体暗地上后滑不静，这不差痕迹变形及网不背增不小无澄辉不良感化。

When setting this home position, the slide cylinder should not be in the deadheaded area of the cylinder -it deadheads approximately 0.25 inch from the absolute maximum distance the cylinder can move.

为了设置初始位置，滑走导向圆柱部不能处于筒体铸件冒口位置—离铸件冒口的绝对极大值是大约0.25英寸，并能使筒体活动。

Feed aprons and stock guide plates with different angles and spacing are being equipped inside the cylinder, the structure can ensure that the material being dried runes along the direction of screwing under the impact of gravitation and keeps for a sufficient maintaining times and dispersity in the cylinder to make the material has sufficient heat exchange with the heat airflow from air heating furnace inside of the cylinder.

三筒烘干机是引进欧洲先进技术，由三个不同直径的同心圆筒彼此相嵌组合而成的。筒内装有不同角度和间距的扬料板和导料板，这种结构能够保证被烘干物料在重力作用下沿着螺旋的运动方向运动，在筒内保持足够的停留时间和充分的分散度，使被烘干物料在筒内与来自热风炉内的热气流进行充分的热交换。

The company Dongfeng Cummins B, C, L series engine cylinder block, cylinder head, crankshaft, piston, valve, cylinder, pump, air compressor, oil pump, flywheel, pressure plates, clutch nearly a thousand varieties of film, etc..

公司现有东风康明斯B、C、L系列发动机缸体、缸盖、曲轴、活塞、气门、缸套、水泵、空压机、机油泵、增压器、高压油泵、飞轮壳、压盘、离合器片等近千个品种。

The company specializes in developing and manufacturing Brake Master Cylinder, Brake Wheel Cylinder, Caliper, Clutch Cylinder, Vacuum Booster, Power Steering Pump etc. These products apply to various cars.

公司致力于：汽车制动总泵、制动分泵、制动钳、离合器泵、真空助力器、转向助力泵的开发和制造，产品适用于各种轿车车型。

When a cylinder and a taper have the same undersides and the same heights, the bulk of the cylinder is 3 times as the bulk of the taper, and the bulk of the taper is 1 third of the bulk of the cylinder.

生：当圆柱和圆锥等底等高，圆柱的体积是圆锥的3倍，圆锥的体积是圆柱的1/3。

In the paper, the simulation model of port plate/cylinder block frictional pair in which the lubricating film forms was established according to force balance equation and flow continuity equation with SIMULINK of MATLAB. The frictional pair includes of damp groove type continuous oil supply port plate /cylinder block frictional pair and semi-perimeter double oil groove type periodical oil supply port plate /cylinder block frictional pair.

本文根据配流副数学模型中的力平衡动态方程和流量连续方程，利用数学仿真软件MATLAB中的SIMULINK工具包分别对阻尼槽型连续供油配流副和半周槽双油腔间歇供油配流副建立了润滑膜形成的仿真模型，并对不同工况下的这两种配流副润滑膜的形成及变化规律进行动态仿真研究。

The results shown that the oil-saving rates of fuel oil and lubricating oil are 5 % and 50% respectively by using GRT energy-saving oil additive, it have reached the level of same kinds of products in 80's from abroad; the cylinder wear of DONGFENG truck and JIEFANG was reduced by 24% and 33% respec-tively; the GRT additive improved obviously the seal property of engine cylinder, not only increasing the cylinder pressure nd the output power of engine to rise the acceleration and cold starting properties, but also improving the combustion situation of the fuel oil to decrease the environmental pollution from the exhaust of truck.

结果表明，应用GRT节能油添加剂可以分别节约燃料油5％以上和机油50％以上，达到了八十年代国外同类产品的先进水平；能使东风牌汽车和解放牌汽车的汽缸磨损分别降低24％和33％以上；使用GRT添加剂可以明显地改善发动机汽缸的密封性，不仅提高了汽缸压力和发动机的输出功率，使其具有良好的加速性和冷起动性，而且改善了燃料油的燃烧状况，从而减少了汽车尾气对环境的污染。

Looking for direction is my one and only direction,ceaseless footstep is my end-result.

寻找方向就是我唯一的方向，不停的脚步就是我的归宿。

Here's how I do the temporary nocks.

这就是握怎么做临时凹槽的。