查询词典 cylinder

Connected with trail research, this paper discusses synthetically the lacks of head-feed rice-wheat combine harvester and its' advancements on technology, and the current of the development on technology of head-feed combine harvester made in Japan in such as the header, the conveying-feed unit, the threshing cylinder, the cleaning unit and the rubber crower w...

分析了日本半喂入稻麦联合收割机在使用中存在的不足以及在收割、输送、脱粒、清选和行走机构等方面技术改进和发展动向。研究表明，以上技术进步进一步提高了半喂入联合收割机技术性能，可为我国半喂入联合收割机的研制提供借鉴。

The coercivity follows the cubic equation with the content of carbon nanotube. Based on the classical hysteresis theory, a new inclusion theory with the cylinder morphology is developed, combined with stress theory the expression of coercivity is given.

基于传统的磁滞机理，发展了具有圆柱形状杂质的含杂理论，结合应力理论，给出了复合材料的矫顽力的表达式，不同体积含量的碳纳米管的复合材料的磁滞机理由含杂理论和应力理论协同控制。

The construction of acetylene cylinders is shown by the cutaway views: Figure 1, the large, and Figure 2, the small type cylinder.

乙炔钢瓶的结构如截面图1和2所示，图1是大钢瓶，图2是小钢瓶。

This forces hydraulic fluid through a pipe to the cutch release cylinder where another operates the clutch disengagement mechanism by a cable .

这迫使液压油通过管道向cutch释放汽缸，另设有离合器脱离接触机制，由一个电缆。

This paper has created the mathematical model of the hydraulic system of the steel bar cutter, considered the hydraulic power unit, accumulator and hydraulic pipe, specially the dynamic characteristics of the hydraulic cylinder buffer structure.

本文建立了高速钢筋切断机液压系统的数学模型，充分考虑了液压动力元件、蓄能器及液压软管等元件的影响，着重分析了液压缸缓冲结构的动态特性。

The experiment results indicated, the results of the position of the cylinder in the high-speed steel bar cutter and the results get by simulation were same, that approved themathematical model was correct and the model machine could put into operation.

实验结果表明，高速钢筋切断机的运动规律与仿真所获得的规律一致，证明了系统数学模型的正确性及样机投入生产的可行性。

In this paper, the cyclic transient temperature field in cylinder head of a gasoline engine,which runs in rated conditions,is analyzed by ANSYS.

以某汽油机气缸盖为研究对象，借助有限元分析软件ANSYS，计算了标定工况下气缸盖循环瞬态温度场。

Not only is the air in the cyclinder being compressed, the leaking air also exerts downward force on the cylinder robbing more power.

不仅是空气中的cyclinder被压缩，空气泄漏也产生向下力缸掠夺更多的权力。

The high cylinder pressure from the power stroke is relieved once the exhaust port is opened, but when it closes off as the piston travels up, the remaining air in the cyclinder is compressed - robbing energy.

高气缸压力的电力缓解中风后，排气口被打开，但是当它关闭的关闭活塞旅行了，剩下的空气压缩cyclinder -抢劫能源。

Plastic should lower 3 steps, because plastic is a step to add melt resin material to cylinder , Higher stick of resin material ,higher screw back pressure. Screw speed differs depending on decomposing temperature of resin material ,Higher screw speed ,Higher trim force of resin, higher cyclinder temperature. Some resin material may decomposes so it set screw speed in mid-speed such as 45-75%, In plastic step setting screw back pressure is very important, Higher screw back pressure ,higher quality of product screw back pressure make resin structure order, Molding product is beautiful and volume stable.

再复杂的熔胶旋转过程最多不会超过三段，因为熔胶本身就是存在于把胶熔进料筒的过程，如果原料粘度大，熔胶压力则大，但速度则应取决于原料的分解温度，熔胶速度越快，原料中的剪切力则会越大，料管温度则越高，局部原料产生分解的可能性则会越大，故一般熔胶会采用中速为宜，如45%-75%，熔胶同时会碰到一个比较重要的环节，那就是背压的使用，产品精度要求越大，背压的使用则更大，背压可使原料分子间结构更紧密，成型出的产品则尺寸更稳定，外观越好。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。