查询词典 cylinder

The influence of different direction between plate cylinder and doctor blade,and different plate cylinder speed on dot gain in gravure printing was discussed.

主要研究了凹版印刷采用刮墨刀与印版滚筒相同和相反方向以及不同印版滚筒速度对网点增大值的影响。

This control method can provide back-pressure cylinder to limit the speed, so the speed stability is good, commonly used in the double-acting cylinder speed control.

这种控制方式能为气缸提供背压来限制速度，故速度稳定性好，常用于双作用气缸的速度控制。

This thesis takes the four-cylinder double-acting Stirling engine as the research key. Based on the Schmidt analysis method, all kinds of flow friction losses and heat losses are analyzed and a model which adapt to the performance of the four-cylinder double-acting Stirling engine is built.

本文以四缸双作用斯特林发动机为研究重点，首先阐述了模拟斯特林发动机的施密特分析法，进而分析了四缸双作用斯特林发动机工作过程中存在的各种流动阻力损失和热量损失，建立了适用于模拟四缸双作用斯特林发动机性能的模型。

Cylinders with a full-length eductor tube, or what is sometimes called a full-length dip tube, have a tube that runs from the inlet of the cylinder valve to the bottom of the cylinder .

带有全长排放管，或者有时称为全长汲取管的钢瓶有一个从钢瓶入口一直伸到钢底部的管子。

For instance, a chiral or dielectric or conduct circular cylinder, a chiral or dielectric or conduct elliptic cylinder. 5. A general program to calculate any order and any type Mathieu function and its derivation is compiled.

编制了计算任意类、任意阶马丢函数及其导数的程序，此程序解决了多种不稳定性，通用性强，对计算没有任何附加限制，在普通微机上即可保证较高的计算精度和速度。

The scattering by different shape and different media such as dielectric chiral or conduct circular cylider or elliptic cylinder are calculated and RCS curves are maped. The relation between the optimal polarization of the chiral elliptic cylinder and incident angle are maped. In accordance with the map, the information which is useful for radar target identification can be obtained.

对不同形状及参数的导体圆柱、椭圆柱，一般介质圆柱、椭圆柱，旋波媒质椭圆柱的散射特性进行了计算，给出了其RCS的变化曲线，并对极化散射矩阵进行了分析给出了旋波媒质椭柱最优极化的分布图，指出了其可提取用于目标识别的极化信息。

This paper discusses the principle of ensilage in twining type of straw bundle cylinder, and necessity of developing the machine twining for plastic film round straw bundle cylinder.

本文论述了圆草捆缠绕式青贮的原理，以及发展圆草捆缠膜机的必要性。

The utility mode comprises a float chamber(1),a float(2), a meter tube(3), a spacing ring(4), a collar(5), and a guiding ring(6), the float(2) is arranged inside the spacing ring(4), the meter tube (3) is a conical tube, the core-and float flowmeter(3) is a guiding cylinder with different diameters, the guiding cylinder matches for the inner wall of the meter tube.

包括浮子室(1)，浮子(2)，测量管(3)，限位环(4)，挡圈(5)，导向环(6)，所述的浮子(2)的上端置于限位环(4)内，所述的测量管(3)为锥形管，所述的浮子(2)为直径不等的导向圆柱体，该导向圆柱体与所述的测量管(3)的锥形内壁配合。

Firstly, the equation for stress intensity factors under static uniform pressure is used as the reference case, and then the weight function for a thick-walled cylinder containing a radial edge crack can be worked out. Secondly, the dynamic stresses in uncracked thick-walled cylinders are solved under internal impulsive pressure by using mode shape function method. The solution consists of a quasi-static solution satisfying inhomogeneous boundary conditions and a dynamic solution satisfying homogeneous boundary conditions, and the history and distribution of dynamic stresses in thick-walled cylinders are derived in terms of Fourier–Bessel series. Finally, the dynamic stress intensity factor equations for thick-walled cylinder containing a radial edge crack subjected to internal impulsive pressure are given by dynamic weight function method.

首先采用静态内压下的应力强度因子作为参考解，得到了带径向边裂纹厚壁圆筒的权函数；然后用振型函数方法推导无裂纹厚壁圆筒在冲击内压下的动应力响应，分析中将相应的弹性动力学方程解分为满足非齐次边界条件的准静态解和满足齐次边界条件的动态解的叠加，利用傅立叶-贝塞尔级数展开，推导出了厚壁圆筒内动应力的响应历程和分布规律；最后由动应力权函数方法导出带径向边裂纹厚壁筒在冲击内压下的动态应力强度因子计算公式。

At present mainly produces single-cylinder, small and medium-power multi-cylinder diesel engines, small diesel industry in the national product variety of the most full-power coverage of the widest main products have independent intellectual property rights of enterprises.

目前主要生产单缸、多缸中小功率柴油机，是全国小柴行业中产品品种最全、功率覆盖面最广、主导产品均有自主知识产权的企业。

I can not make it blossom and suits me

我不能让树为我开花

When temperatures are above approximately 80 °C discolouration of the raceways or rolling elements is a frequent feature.

当温度高于 80 °C 左右时，滚道或滚动元件褪色是很常见的特征。