查询词典 cylinder-shaped

From the strength of the cylinder in the platen press ,the relations between the allowable stress of material to make the cylinder and the hydraulic pressure are derived when the outer diameter of the cylinder is the minimal value.

根据平板硫化机液压缸圆筒部分的强度条件，推导出液压缸外径为极小值时，液压缸材料的许用应力与工作液压力之间的关系，从而为平板硫化机的优化设计提供了最佳工作液压力值。

This paper studies on the impression cylinder of J2108 offset press. With finite element method, deflection character of cylinder is achieved in static and dynamic load. Active-compensation to improve flexing-change of cylinder is bring forward, and its compensation character is simulated.

本文以J2108型胶印机压印滚筒为研究对象，通过有限元分析获得滚筒动静态挠曲特性，提出用主动补偿方法改善滚筒挠曲变形，并仿真分析了补偿特性。

On the basic of heat equation method, a general math modeling of heater is developed., as well as a lots of real-time math modeling of heating system, such as math modeling of heat economic analysis、relative internal efficiency of HP cylinder、relative internal efficiency of MP cylinder and LP cylinder、utilization of blow down water tank、steam make-up of deaerate and steam leakage of seal gland.

热力系统在线性能计算和热经济性分析在降低机组煤耗，提高火电厂运行效益方面具有重要的作用。

If the gap is too large, when the cylinder pressure cannot be effective to brake-workholders, causing tension too small, resulting in a post by floating roll drawn paper tape under; if the gap is too small, the cylinder is always workholders, brake cylinder pressure cannot adjust the brake pad and brake disk workholders degrees, and there will be draggle the paper tape.

如果间隙过大，当气缸气压变化时不能有效地将刹车片夹紧，导致张力过小，造成开机时浮动辊突然被拉下将纸带绷断；如果间隙过小，则气缸始终将刹车片夹紧，气缸气压变化不能调整刹车片与刹车盘的夹紧程度，最终会将纸带拉断。

An end cover which can be taken out by fingers sets on the inner end of the carriage of the outer cylinder, the end cover prevents eyewinker from passing through the gap between the outer cylinder and the drive transfer component to immerge into the outer cylinder.

在外筒的车厢内侧端部，可用手指取出地设有端盖，该端盖防止异物经过上述外筒与上述驱动力传递构件之间的间隙而浸入到外筒内。

This kind of structure cylinder that ultrahigh pressure is produced in the work cylinder interior, does not affect the tubing, made the system seal to be simple, and it enables the small fluid pumping station to drive the hydraulic cylinder.

这种结构的液压缸超高压只在工作液压缸内部产生，不波及油管，使整套系统密封简单，实现了小液压泵站驱动大作用力液压缸的目的。

Concrete and other hydraulic cylinder used new technology and new technologies, using concrete cylinder block IF processing technology, using carbon and nitrogen sulfur fuel tank rod permeation technology, the service life of the fuel tank and concrete cylinder life greatly increased.

另外液压油缸和砼缸采用新工艺和新技术，砼缸缸体采用中频处理技术，油缸活塞杆采用碳氮硫共渗技术，使油缸使用寿命和砼缸使用寿命大大增加。

In the absence of any mention of cutting facilities, and dividing the work required in advance of hydraulic cylinder pressure is low, it pumps to large flow into the hydraulic cylinder, graduated cylinder moving fast.

因无任何节流设施，且分度液压缸前进时所需工作压力低，故泵以大流量送入液压缸，分度缸快速前进。

For the minimum dry density test of sand, test devices are improved to simplify the procedures and the test steps are adjusted to reduce the measurement error. The reverse graduated cylinder method and the tilting graduated cylinder method are recommended as the best methods for minimum dry density test and for leveling sand surface respectively. The optimum sampling quantity and the times of reversing graduated cylinder are studied.

对最小干密度试验，改进了试验装置以简化操作手续；调整了试验步骤以减小测量误差；推荐只使用量筒倒转法测量，用量筒倾斜法整平砂面；研究了最佳取样量和量筒倒转次数。

During the beginning （about 3-5 seconds） of operating "Compress" key for oil cylinder handspike to move downwards, push the trash feeding door or pull the main door, hydraulic oil cylinder handspike stops immediately,"Compress" light goes out, discontinuous ringing arises, and the screen shows "Breakdown"; reset the door, the ringing stops, and the screen shows "Compress"; after hydraulic oil cylinder handspike automatically returns to the original place, indicator light "Compress" goes out.

在操作"压缩"键使油缸推杆向下运动后的最初时间内（约3-5秒），推动垃圾投入门或拉开大门，液压油缸推杆立即停止运动，"压缩"显示灯灭，产生缓慢间歇讯响，显示"故障"；门恢复后，停止讯响，显示"压缩"，液压油缸的推杆自动回到原始位置后，指示灯"压缩"灭。

Through comparing with the results by simulation to study the effects of theprojectile"s final velocity, the angle of rotation and the ballistic trajectory"s migration withdifferent projectile"s rotating speeds, different target"s moving speeds and differentpenetration angles.

通过比较数值模拟的结果来研究不同弹头转速、目标速度、侵彻角对侵彻过程中弹头最终速度、翻转角度和弹道偏移的影响。

I love stationery and all the accoutrement of writing.

我爱文具以及所有的书写的工具装备。