查询词典 cylinder mill

For the engine, the cylinder block, cylinder head and the crankshaft are the import roughcast.

经测试和使用验证，该发动机表现在国内同类产品中是相当突出的。

In practical experiment on a ceramic cylinder gyroscope, it shows that the resonant frequency is quite approximate to the simulated one. A good linear relation of the sense voltage to rotation speed is obtained, which indicates the piezoelectric ceramic cylinder gyroscope is good at the measurement for low and medium rotation speed.

在圆柱型陀螺仪之实验过程中，显示驱动与感测之共振频率几乎为一致；而在旋转实验中得到转速与感测电压拥有良好的线性关系，亦指出该陀螺仪在中低转速下拥有较佳之线性关系。

Where possible, the purge gas cylinder pressure should be maintained at a level higher than the silane cylinder pressure.

在可能的地方，净化气体钢瓶的压力要维持在高于硅烷钢瓶压力的水平上。

In technical transformation of SNG-H300 high-pressure water injection pump ,LT3404 horizontal 3-cylinder single-action plunger pump substitutes original 2-cylinder double-action piston pump to improve technical performances and reliability and increase economic efficiency.

对SNC-H300高压注水泵进行技术改造，用"LT3404卧式三缸单作用柱塞泵"代替原有的双击双作用式二缸活塞泵，以提高技术性能和工作可靠性，提高经济效益。

Production plant is built by Liwo machining centers, CNC horizontal boring and milling machines, CNC milling machine portfolio composed of "soft-shell parts production line": production block, cylinder head, gearbox, and other high technology content Shell exports of parts and vehicles and Liwo Liwo CNC machining centers, and other components of the "revolving line of processing": processing the internal combustion engine piston, cylinder differential top shell, shell reducer such as automobiles, engineering machinery, Agricultural machinery industry with high technical content in the rotating parts, as well as between the rotating shell parts and exports between the parts production.

现生产工厂已建由立卧加工中心、卧式数控镗铣床、数控组合铣床组成的"壳体类零件准柔性生产线"：生产缸体、缸盖、变速箱等各种技术含量高的壳体类出口零件；以及数控立卧车和立卧加工中心等组成的"回转体加工线"：加工内燃机活塞、缸头等差速器壳体、减速器壳体等汽车、工程机械、农机行业中技术含量高的回转体零件以及介于回转体和壳体类零件之间的出口零件生产。

Car flooded the water will enter the engine from the inlet resulting in engine flameout this time there will be water accumulation in the cylinder chamber and spark plugs in braving the water if the owner starts the engine the piston will Top connecting rod bend or even cylinder head roof leak causing irreparable damage.

车被淹后，水就会从进气道进入发动机，从而导致发动机熄火，这时候就会有水吞积在汽缸室，而火花塞在顶着水的情况下，如果车主启动发动机，就会把活塞连杆顶弯，甚至将缸盖顶漏，造成安全阀不可挽回的损失。

Three kinds of swirl meter are used to measure the swirl in different cross section of a diesel engine cylinder on a stationary flow test bench. This paper analyses the influence on incylinder swirl measurement of the type of swirl meter, measuring position and flow distribution in-cylinder.

本文在稳流模拟试验台上，利用三种涡流计测量了不同横截面高度的缸内涡流，分析了涡流计型式及测速位置对缸内涡流转速测量结果的影响，阐述了缸内速度分布对涡流测量影响的变化规律。

According to geometry model characteristic of shaft and cylinder of steam turbine, a finite element method model of shaft and cylinder was set up.

根据汽轮机转子及汽缸的几何模型的特点建立了转子及汽缸的有限元模型。

Based on the hydraulic cylinder product stylebook of the enterprise, we designed an easy application of management information system of hydraulic cylinder, which mainly includes building up database of back-end and developing the application interference of front-end.

本课题以企业液压缸产品为样本，设计了一套简单的液压缸产品数据库管理系统，其开发主要包括后台液压缸系统数据库的建立和维护以及前端应用程序的开发两个方面。

Clean the accumulated carbon in the combustion chamber, take off the cylinder head seal gasket and clean the sealant on the cylinder head joint surface.

清除燃烧室内的积碳。取下缸头密封垫，清理缸头结合面密封胶。

Nowadays, most of research are to build a transmutative Petri Nets through adding controlling place sets, controlling arc sets and controlling policy to the basic Petri Nets, while the Controlled Petri Nets could be used to argue many controlling theory problems conveniently and to induce many logically and physically supervisory and solve the Event Feedback Controlling Problems and State Feedback Controlling Problem in DEDS supervisory theory.

目前大多数的研究表现为在变形后的受控Petri网基础上，利用各种方法求得各种逻辑型、结构型控制器，解决DEDS监控理论中的事件反馈控制问题与状态反馈控制问题。

On one hand, there are discussions with the works council and union about extension of short time working up to the end of September.

一方面，有讨论，工程理事会和联盟关于延长工作时间短至9月底。