查询词典 cylinder mill

The theoretical and computational results show that an important reason resulting in eccentric wear of the inner cylinder and the pumping rod lies in the nonuniformity of the stress distribution on the outwall of the inner cylinder which yields excentralization effect of the pumping rod when swabbing fluid flows in eccentric annuli with the pumping rod moving axially in a well.

在实验上，通过不同重量百分比浓度的HPAM水溶液在内管做轴向往复运动的偏心环空中非定常流实验，把由理论公式算得的时间平均流量与实验中测得的时间平均流量做了比较，验证了本文数值计算幂律流体在内管做轴向往复运动的偏心环空中非定常流方法的正确性；上述的理论与计算表明，抽油机井杆管偏磨的一个重要原因是，在聚驱工况下，抽汲液体在抽油杆做轴向运动的井筒中流动时，抽汲液体作用在抽油杆外壁上的压力分布的不均匀性所引起的抽油杆在井筒中的偏心效应。

In the turbo and 6-cylinder Legacy and Outback models equipped with the 5-speed automatic transmission (standard on 6-cylinder models), new steering wheel paddle shifters add a new dimension of driver involvement.

在涡轮增压和6缸的遗产，并与5速自动变速器（标准配备6缸机型），新的方向盘换档配备内陆模式向司机参与的新的层面。

Based on the structure of a non-tracking internal-concentrator solar PV-thermal tube collector and the absorber design requirements, the optical design for the compound parabolic concentrator with half cylinder absorber is proposed to improve the solar energy efficiency. Matlab software was used for the optimization and simulation of the concentrator curve and shape. The curve equation of concentrator for maximum incidence of light of the collector was obtained; and the installation locations for CPC/half cylinder absorber and the necessary CNC processing parameters were optimized.

针对非跟踪内聚光光电－光热复合管的结构及接收器的设计需求，对管内具有特殊形状的半圆柱接收器的复合抛物面聚光器进行了光学设计，并利用Matlab软件对聚光器曲线和形状进行了优化与数据仿真，得到了光热复合管能够得到最大入射光的聚光器的曲线方程、安装位置以及供数控机床加工所需的参数，给出了不同入射角的光线和光强分布图，提高了太阳能的利用率。

Four-valve, pent roof cylinder head design uses two spark plugs per cylinder for efficient combustion and great power delivery at all rpms.

四气门，压抑屋顶缸盖设计采用两个火花塞每个气缸的燃烧效率和巨大的功率输出在所有从RPMS 。

According to the results of stress calculation, provided the choosing basis for structure parameters of hydraulic cylinder and advanced a new cylinder bottom structure-oblique plane check ring concave groove.

对 10MN闭模挤压液压机卡环式液压缸进行有限元应力分析，根据分析结果，给出了液压缸缸底结构参数的选取依据，并在此基础上提出了一种斜面卡环凹槽新结构，有效解决了大型卡环式液压缸卡环凹槽的应力集中问

The printing cylinder and plate cylinder are connected to gears G7 and G8,respectively.

这个 印刷缸，缸是连接到档板，八国集团分别G7.G1是输入齿轮。

However, this would also reduce the effective length of the power stroke because once the exhaust valve opens, there is no longer cylinder pressure to force the cylinder down.

然而，这也将减少有效长度的权力，因为一旦中风的排气门打开时，不再有气缸压力，以迫使缸下来。

Requirements for hydraulic steering rack cylinder are very high, the rack cylinder should be durable, lubricants preservable and of seal.

文摘：液压转向机对齿条杆部表面有很高的耐磨、储油、封存要求，为此需要一套表面超精加工工艺及加工参数设定。

Requirements for hydraulic steering rack cylinder are very high, the rack cylinder should be durable, lubricants preservable and of seal. so, finish machining and parameter-set are necessary.

励锋液压转向机对齿条杆部表面有很高的耐磨、储油、封存要求，为此需要一套表面超精加工工艺及加工参数设定。

The pressure hull is an important element of submarine structure which can withstand the external pressure, the pressure hull is composed of cylinder and dome for the most part, and needs to weld stiffeners on the cylinder within a moderate space.

潜艇在水中主要由压力壳来承受水压，而小型潜艇之压力壳大都由圆筒壳及半球型壳组合而成，并在圆筒壳上之适当距离焊接环状肋骨作为补强。

Nowadays, most of research are to build a transmutative Petri Nets through adding controlling place sets, controlling arc sets and controlling policy to the basic Petri Nets, while the Controlled Petri Nets could be used to argue many controlling theory problems conveniently and to induce many logically and physically supervisory and solve the Event Feedback Controlling Problems and State Feedback Controlling Problem in DEDS supervisory theory.

目前大多数的研究表现为在变形后的受控Petri网基础上，利用各种方法求得各种逻辑型、结构型控制器，解决DEDS监控理论中的事件反馈控制问题与状态反馈控制问题。

On one hand, there are discussions with the works council and union about extension of short time working up to the end of September.

一方面，有讨论，工程理事会和联盟关于延长工作时间短至9月底。