查询词典 cylinder mill

The company specializes in developing and manufacturing Brake Master Cylinder, Brake Wheel Cylinder, Caliper, Clutch Cylinder, Vacuum Booster, Power Steering Pump etc. These products apply to various cars.

公司致力于：汽车制动总泵、制动分泵、制动钳、离合器泵、真空助力器、转向助力泵的开发和制造，产品适用于各种轿车车型。

When a cylinder and a taper have the same undersides and the same heights, the bulk of the cylinder is 3 times as the bulk of the taper, and the bulk of the taper is 1 third of the bulk of the cylinder.

生：当圆柱和圆锥等底等高，圆柱的体积是圆锥的3倍，圆锥的体积是圆柱的1/3。

In the paper, the simulation model of port plate/cylinder block frictional pair in which the lubricating film forms was established according to force balance equation and flow continuity equation with SIMULINK of MATLAB. The frictional pair includes of damp groove type continuous oil supply port plate /cylinder block frictional pair and semi-perimeter double oil groove type periodical oil supply port plate /cylinder block frictional pair.

本文根据配流副数学模型中的力平衡动态方程和流量连续方程，利用数学仿真软件MATLAB中的SIMULINK工具包分别对阻尼槽型连续供油配流副和半周槽双油腔间歇供油配流副建立了润滑膜形成的仿真模型，并对不同工况下的这两种配流副润滑膜的形成及变化规律进行动态仿真研究。

The results shown that the oil-saving rates of fuel oil and lubricating oil are 5 % and 50% respectively by using GRT energy-saving oil additive, it have reached the level of same kinds of products in 80's from abroad; the cylinder wear of DONGFENG truck and JIEFANG was reduced by 24% and 33% respec-tively; the GRT additive improved obviously the seal property of engine cylinder, not only increasing the cylinder pressure nd the output power of engine to rise the acceleration and cold starting properties, but also improving the combustion situation of the fuel oil to decrease the environmental pollution from the exhaust of truck.

结果表明，应用GRT节能油添加剂可以分别节约燃料油5％以上和机油50％以上，达到了八十年代国外同类产品的先进水平；能使东风牌汽车和解放牌汽车的汽缸磨损分别降低24％和33％以上；使用GRT添加剂可以明显地改善发动机汽缸的密封性，不仅提高了汽缸压力和发动机的输出功率，使其具有良好的加速性和冷起动性，而且改善了燃料油的燃烧状况，从而减少了汽车尾气对环境的污染。

Single product with reset cylindrical spring, with loss of gas automatic reset function, which is lost when the gas cylinder piston in the spring under the effect of putting the cylinder back to the cylinder driving the initial location (the original location of travel).

单作用产品带复位圆柱弹簧，具有失气自动复位功能，即失气时气缸活塞在弹簧作用下，驱动气缸推杆回复到气缸初始位置。

Cited Pistons pull vent valve 10-valve piston cited the role of pulling out are seized cylinder piston rod, when its mild in China emerged after the main hydraulic cylinder rod cavity and there is no cavity under the pressure dropped, so that the main hydraulic cylinder in motion the process of increasing resistance to the main pump to increase the load, resulting in engine speed when pumping declining situation.

3活塞引拔阀内泄活塞引拔阀10的作用是拉出检缸活塞杆，当其出现轻度内泄后，主液压缸无杆腔和有杆腔的压差下降，使主液压缸动作过程中阻力增加，使主泵负荷加大，导致泵送时出现发动机转速下降的现象。

The plates of the rollers and rubber roller pressure control in 15 ~ 20 wire, two rubber roller pressure control in the 22-38, 28, and make sure that two rollers by version and parallel plate cylinder, below the 100 mm diameter rollers by Edition and nano-imprint lithography printing plate cylinder is 5-6 mm, more than 100 mm diameter rollers by Edition and nano-imprint lithography printing plate cylinder is 6 ~ CCDs used in àw±a?

不兵印版滚筒与橡皮滚筒之间的不张辛把持在15～20丝、两橡皮滚筒之间的不张辛把持在22～28丝，并包管两不梢靠版不朱辊与印版滚筒交错，直径在100mm以上的靠版不朱辊与印版滚筒压印宽度为5～6mm，直径在100mm以上的靠版不朱辊与印版滚筒压印宽度为6～7mm。

The use of characteristics: 1, can be achieved single-cylinder multi-speed, multi-location, two-cylinder or two-cylinder over a poor campaign, the completion of tracking movement.

使用特点：1、可以实现单缸多段调速、多点定位、两缸或两缸以上进行差补运动，完成曲线轨迹运动。

Information relating to the Yale and Era cylinder type locks, how to position the lock, drilling the cylinder hole, fitting the cylinder mechanism and mounting plate and also fitting the striking plate/ kepper in the door frame.

有关的资料和时代耶鲁缸式锁，如何定位锁，钻缸孔，配件气缸机制和安装板以及配件的突出板/凯珀在门框。

The first to use PRO / E software components establishment of the body (body, cylinder head, cylinder pad, cylinder liner, the main bearing caps, Flywheel carcasses, gear Connection Board Room, Shell pump, oil pan, about mounting frame, rear axle oil blocks, etc.) 3D solid model; Then use Hypermesh software division finite element mesh to ensure a good grid quality, and better coordination of the grid between quantity and accuracy of contradictions; Finally using ANSYS software components of a body finite element analysis.

首先利用PRO/E软件建立机体组件（机体、气缸盖、气缸垫、气缸套、主轴承盖、飞轮壳、齿轮室连接板、水泵壳体、油底壳、左右悬置支架、后轴油封盖等）的三维实体模型；然后利用Hypermesh软件划分有限元网格，保证了良好的网格质量，较好地协调了网格数量和计算精度之间的矛盾；最后利用ANSYS软件对机体组件进行了有限元分析。

You can do some assertiveness training.

你可以进行一些自信训练。

We were well on the path to making a rear-wheel-drive global platform," says Mays."

我们正致力于建立一个后轮驱动的平台，"Mays这样说道。"