查询词典 curve of error

The conception of error compensation is introduced in autocorrelation measurement, and the interferential correlation curve is corrected with a computer.

提出了用计算机对所测相关曲线进行误差补偿的概念。

The secant modulus is used to calculate final settlement of high-stacked soil, compared with the result of e ~ p curve, the error is in the limit of tolerance.

同时将割线模量计算沉降的方法应用到高填方自身作用下的最终沉降计算中，通过与应用e～p曲线计算的结果进行比较，其误差在允许范围之内。

The features to evaluate the tooth contact quality such as the location of the contact point on the tooth surface, clearance between the meshing tooth surfaces, curve of the transmission error and the path of the contact point are investigated. The accurate geometric representation with non-uniform rational B spline of the worm and the wheel tooth surface is presented then the corresponding program is developed.

根据平面包络环面蜗杆传动的创成方法，建立了包含加工误差的蜗杆和蜗轮的齿面方程，分析了平面包络环面蜗杆传动和平面二次包络环面蜗杆传动的刚性啮合特性如误差对接触点的位置、齿面间隙、传动误差曲线和接触点在齿面上的轨迹的影响。

The results show that the experimental results are in good agreement with the values of viscosity in a part of temperature range that has been reported, with the relative error of less than 2.5%; In the process of ascent and descent temperature, the irreversible phenomenon of the curve of viscosity versus temperature V presents interzone characteristic, and the break of viscosity at critical temperature reflects jump change of melt structural information; It is one to one correspondence between viscosity and atomic size, and this relation is consistent with the Hall-Petch formula in expression way.

结果表明：实验结果与已报道的部分温度区间内的黏度值基本一致，相对误差低于2.5％；升温和降温过程中，黏度－温度关系曲线V的不可逆现象具有区间特征，临界温度时黏度的突变反映出熔体结构信息的跳跃变化；黏度与原子集团尺寸之间存在一一对应关系，该关系在表达上符合Hall-Petch公式。

The system can get the signal waveform parameters from the harmonic components of radius vector deviation, plot a curve of interpolation error by delivering magnified moiré fringe photoelectric signal to computer with digital acquisition board.

该系统可以利用数据采集卡，将放大后的莫尔条纹光电信号送入计算机，由向径偏差的谐波成分得到信号波形参数，绘出细分误差曲线。

Adopt software of Surfacer to fit curve and remodel surface, go on analysis of error and continuity, make model surface achieve rang of smooth and precision.

利用Surfacer软件对点云进行曲线拟合以及曲面重构拟合，通过对拟合曲线和自由曲面的误差分析以及连续性的分析，使构造的自由曲面光顺度和精度均满足要求，从而实现理论与实际的相结合。

The differences between the experimental and theoretical binodal curves might be caused by the error of the interaction parameters applied and by the neglect of the concentration dependency of g13 . Key word: Interaction parameters; Flory-Huggins; phase diagram

实验上观察到的液/液相分离现象与理论运算上所得到的结果趋势吻合，但实验点与理论所得到的binodal curve 有些误差，判断乃是由於作用力参数值估算误差，及未考虑g12 的浓度相关性所造成。

This current is extra high and exceeds the permitted value of 10 % error curve of protection current transformer.It will affect the performance of relevant protection equipment.

文中以n次曲线模拟TA铁心饱和时的非线性磁化曲线，由此导出TA回路的非线性微分方程，并采用数值方法计算出在典型暂态短路电流作用下的TA二次电流波形。

Due to capacity increase or structure change of the power system, an extra-high current possibly 100 times of the rated current may appear in some circuits of the power system when a short-circuit fault happens nearby. This current is extra high and exceeds the permitted value of 10% error curve of protection current transformer.

在电力系统中，各回路的最大故障短路电流和额定工作电流的比值应在合理的范围内，以保证保护用电流互感器的工作精度，但由于系统容量增大或因系统结构等原因，某些回路在某些情况下的最大故障短路电流远远超过了正常范围。

In an admirable error bound, the numerical simulation had the close results with experiment by the characteristic curve of cold mass flow fraction, as well as Thermodynamics model of vortex tube, So Thermodynamic theory hypothesis was available to explain Ranque-Hilsch effect of vortex tube.

在误差允许的范围内，涡流管冷流率特征曲线描述的结果与涡流管热力学理论给出的结果非常相近，说明涡流管热力学理论假设能够描述Ranque-Hilsch效应。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐