查询词典 curve of error

The varies regression curves have been adapted to calculate moisture in order to increase device precision and overcome the shortcoming of big error at high moisture when using single curve. 3 Varies scope output signal are changed to 4～20 mA and sent to computer over the share-voltage compensation circuit. The multi channel sensor could be auto chosen to display lumber moisture in different position of the kiln. It makes the moisture distribution of lumber in the kiln clearly and drying standard accurately.

所以采用不同的拟合曲线对水分进行换算，以便提高仪器精度，并克服单一曲线造成的高含水率时误差较大的缺点；3：采用分压补偿式测量电路，将不同量程的输出信号转换成统一的4～20mA信号，送至计算机进行集中数据处理；并自动控制多路传感器的选择，分时显示干燥窑中不同部位木材的水分，使整个窑中木材水分分布一目了然，便于准确地制定干燥基准。

We present a method of circular arc fragmented curve-fittingbased on least mean-square error rule in this paper.

谭勇 ，徐守时，涂嘉文提出了一种基于最小均方误差准则的圆弧分段曲线拟合方法。

From the experiment's data, before sampling I have analysed the shortage of the ACCUSTAR angle sensor, plot its error curve and established linear drawing up to match to correct it. Then I will adjust it to zero and set a mark before using it, and improve the examining environment.

本课题研究了此倾角传感器的具体特性，从实验数据着手，先是分析了传感器本身的物理缺陷，描绘出了它的非线性特征曲线，并制定了专门修正它的线性拟合修正法；其次是在使用前，在检测现场对传感器进行了调零和定标，并且对实验现场的环境进行了改善。

Full-featured protection of CT-V characteristics can be tested, 5% and 10% error curve, variable ratio, polarity, but also can output high current is used to test CT secondary circuit.

功能全面可测试保护CT伏安特性、5％和10％误差曲线，变比、极性，还可以输出大电流用于测试CT的二次回路。

Among routine three impulse control system, because reason of " false liquid location" make steam load rise and drop dynamic characteristic when curve asymmetric, degeneration, can't ask out the accurate mathematics model when and there are the systematic parameters, can't design the accurate feedforward controller either, can only realize the static feedforward , can realize that there is not error in the stable state , but does not control dynamic performance well.

而在常规的三冲量控制系统中，由于&虚假液位&的原因使得蒸汽负荷上升和下降时的动态特性曲线不对称，且系统参数具有时变性，不能求出准确的数学模型，也就不能设计出准确的前馈控制器，只能实现静态前馈，能实现稳态无误差，但对动态性能控制不好。

The article elaborates the basic theory and mathematics model of ablating cornea by Excimer Laser, makes out the model which partition the cornea ablation area to 30 or 60 ablating circles, and arrives at the error of real calculation corve and academic model curve by comparing a with them under the help of MATLAB software, achieves the success of coney experiment and blind eyes' experiment, thus establishes the clinical experiment basis of cornea ablation in advance.

文章论述了准分子激光消融眼球角膜的基本原理和数学模型，提出了把角膜治疗区域有目的地划分成30个或60个消融道的模式，通过MATLAB软件把理论计算曲线和实际模型曲线进行比较，得出它们的消融误差，并且成功进行了动物实验和盲眼实验，提前为角膜屈光的临床实验奠定了基础。

Through the curve fitting,the almost real angle is obtained,which is used in the correction of the time-lag error.

数值分析的结果表明，通过修正时延偏差能有效地改善弹丸斜入射对定位精度的影响。

The error analysis shows the fitting curve is almost accorded with the measured one.It reveals the change rules of radiation temperatures of objects which are made of material with different emissivities with skin temperatures.

误差分析表明，拟合曲线与实测曲线基本吻合，反映了使用不同发射率材料的目标的辐射温度随表面温度变化的规律。

Based on the modeling theory of the equivalent probability density error model(marked as "Tepdem") and the numerical algorithm,this paper provides an approach on how to ascertain a point location with the highest coordinates precision between both of the adjacent characteristic points on a generic curve accurately by use of the theory of function extremum as well as the iterative algorithm,and it also provides the method on how to obtain the least width of "Tepdem" exactly,from which,the explanation of geom...

基于等概率密度误差模型建模原理和数值算法，运用函数极值理论和迭代方法来求解平面一般曲线上两相邻特征点间位置精度最高的点，以精确确定误差模型的最小带宽，从理论上给出等概率密度误差模型的几何特征，从而进一步完善矢量GIS的位置不确定性理论。通过实例计算与可视化分析，验证了理论推导的正确性。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐