查询词典 cubic

In view of the problems in the traditional highway vertical curve design,the cubic interpolation spline function replacing the conventional curve is proposed and the formula of function is demonstrated.

针对传统的公路竖曲线设计中存在的一些问题，可提出使用三次插值样条函数来替代传统线形的思路。

A software code was programmed based on the established panel arrangement principles and the special cubic spline function.

基于该程序所生成的网格，更能体现船体实际形状，并能为兴波阻力计算程序提供高质量的网格。

With thw cubic B spline function treated as displacements, the spline element stiffness matrix is established based on the principle of minimum potential energy.

用3次B样条函数来构造结构的位移模式，基于最小势能原理导出了桥梁结构的样条单元刚度矩阵。

Lastly,the distortion's rules fitted by cubic spline function were used to restore the distortion image captured by the same visual system.

最后，用该样条函数拟合的桶形畸变规律对同一个视觉系统拍摄的变形图像进行恢复。

For acquiring the mean line of workpiece profile,a new kind of digital smoothing filter based on cubic generalized spline function was proposed.

为了提取工件表面轮廓中线，给出了一种基于三阶广义B样条函数的数字光滑滤波器。

Prepared by the cubic spline interpolation function, TSS method diagonal matrix equation function, interpolation function point value function.

C#编写的三次样条插值函数，TSS法求解对角矩阵方程函数，插值点函数值计算函数。

After summarizing the existing research results, this article proposes new methods on moving force identification based on radial basis function approximation method and cubic spline function approximation method, and discusses the influence which some parameters to the precision of identification through calculating an example.

文章首先在第一章中介绍了已有的移动荷载识别方法及国内外的研究状况，在此基础上提出了研究目标和意义，即提出新的移动荷载识别方法，并通过数字模拟来讨论新方法的精度，以便评估桥梁的动力特性，为桥梁的设计和汽车性能的改进提供依据。

In this paper, therefore, a new interpolation method using cubic spline function is presented for range migration correction. Using the method we presented, SAR imaging simulation of point target has been done and the experiment results are satisfactory.

作者用三次样条函数插值进行距离徙动校正，进行了点目标SAR仿真成像，得到了满意的仿真结果。

Interpolative control; Cubic spline function; Simulation; Error

插值控制；三次样条函数；仿真；稳态误差

This paper presents the design of the software and hardware of the microcomputer aided DGF5 Peak Inductive Transduser data collecting system,analyzes the important error sources,works out the method of using cubic spline function to modify the system error,and puts forward the relative software.

介绍了用IBM－PC系列微机与DGF－5型电感测微仪构成的数据采集系统的软硬件设计，对系统的主要误差源进行了分析，提出对系统的综合误差用三次样条函数拟合补偿的方法，并设计了相应的软件。

You can do some assertiveness training.

你可以进行一些自信训练。

We were well on the path to making a rear-wheel-drive global platform," says Mays."

我们正致力于建立一个后轮驱动的平台，"Mays这样说道。"