查询词典 crystallization

The results show that after adding B nucleator , the crystallographic form of PP was transformed fromαtoβ, the initial crystallization temperature increased obviously, the total crystallization time shortened.

结果表明，添加β晶型成核剂后，PP由α晶型向β晶型转变，起始结晶温度明显提高，总结晶时间缩短，结晶活化能降低。

The rheological and crystallization behaviors of PP/EOC blends showed that increasing octene content in EOC elastomer resulted in a decrease of EOC fluidity, an increase of the adhesive fracture energy with PP and of hindering PP crystallization.

研究了PP／EOC体系流变和结晶行为，发现随辛烯含量的增加，EOC流动性变差，与PP的界面粘结能增大，即相容性提高，对PP结晶的阻碍作用增强。

The model of programmed crystallization of SPM was proposed based on the moment transformation of the population considering the agglomeration. The optimal temperature-time curves in a batch crystallizer which maximized the terminal mean size and mean weight size can be determined from the application of the Pontryagin Maximum Principle. The calculated crystallization results heating under optimal temperature were compared with ones under linear or natural heating temperature.

根据第四章所得到的螺旋霉素晶体二次成核和晶体生长和布朗扩散引起的聚集动力学，利用第六章所描述的晶体尺寸分布的各阶矩对时间的一阶导数所构成的自封闭的一阶常微分方程组，采用庞得里亚金极大值原理，以温度为控制变量，在满足某些约束条件下，以最大平均尺寸和最大晶体重量平均尺寸为性能指标，计算出了螺旋霉素间歇结晶的最优温度—时间曲线，并同线性加热和自然方式进行了比较。

Optimization of resolution conditions and affecting factors on resolution such as solvent, the molecular ratio of racemate to resolving agent, method of reaction, concentration of racemate, crystallization temperature and crystallization time were studied.

对影响拆分的因素溶剂和底物浓度通过均匀实验进行了优化，同时对其他影响因素如底物与拆分剂投料比、反应物溶解方式、结晶时间和结晶温度等进行了考察。

The best conditions were: ethanol/acetone as solvent, molecular ratio of racemate to resolving agent 1.0:1.0, using heating as method of reaction, concentration of racemate 20mg/ml, crystallization temperature 1℃, crystallization time 8 days.

最佳结果为：乙醇／丙酮一 5.85，则为溶剂；L＜一卜苹果酸与佐匹克隆摩尔投料比为10二0；佐匹克隆20mg／ml；反应物溶解方式为加热处理；结晶温度l℃；结晶时间sd进行拆分。

Using the analysis of differential scanning calorimetry, three exothermic peaks were found which were mainly attributed to crystallization of α-(373℃), relaxation of internal strain (410℃) and crystallization of the residual amorphous matrix (540℃) respectively.

对机械合金化形成的非晶〓的DSC测量表明：在40℃到700℃范围内，有三个位于373℃，417℃和540℃左右的放热过程，分别α-相的结晶，内应变的降低和残余非晶相的晶化。

The crystal-lization of this amorphous alloy is a multi-stage continuous nucleation up to saturation process. The local crystallization energy decreases gradually indicating that the thermal stability of the residual amorphous matrix becomes weak at the steady crystallization stage, which is ascribed to the diffusion of boron atoms at elevated temperatures.

进一步研究发现，该非晶合金的晶化为多阶段的连续形核直至饱和的过程；当进入稳定晶化阶段时，剩余非晶的局域晶化激活能逐渐下降，非晶基体的热稳定性降低，这是由B原子的高温扩散导致的。

Nano-SiO2 particles can also increase the crystallization temprature and crystallization rate of PP and decrease its size of spherulite.

纳米SiO2可提高PP的结晶温度和结晶速度，并使球晶细化。

The spherulite growth rates of PPS were measured in the range of crystallization temperature from 235 ℃ to 265 ℃ as a function of crystallization time.

采用热台偏光显微镜技术观察了聚苯硫醚及其玻璃纤维、炭纤维及芳纶纤维增强复合材料等温结晶过程中球晶结构形态的变化。

Spherulite was firstly observed in the system and the formation, growth and evolvement of spherulite were its crystallization behavior, which was different from other mica-based glass-ceramic systems. Expital growth also was one of the crystallization behaviors.

首次在此体系发现了球晶，球晶的形成、生长和演变是本体系不同于其它云母体系的晶化形式；外延生长也是主要的析晶方式。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。