查询词典 cross girder

The project used in conjunction with three holes of a prestressed continuous box girder design, layout for cross-bridge 30m +30 m +30 m, two-way four-lane bridge to meet current conditions, after the completion of the construction of the bridge under the bridge to meet the 8-lane two-way traffic conditions.

本工程采用三孔一联预应力连续箱梁设计，桥跨布置为30m+30m+30m，桥上满足双向四车道通行条件，建设完成后满足桥上桥下双向8车道的通行条件。

The cross girder center segments of the bents were field bolted.

构架横梁的中间段在工地用螺栓连接。

Two bars of belt chain fire grate; two flakes of small louver fire grate; one middle clamping sheet; one side clamping sheet; two flakes of large louver fire grate; one middle clamping sheet of large louver fire grate; one side damping sheet of large louver fire grate; one roller; two bars of cross girder fire grate; one adapter; two flanges; one valve body.

产品/Product：炉排付片二件；小鳞片炉条二件；中夹板一件；边夹板一件；大鳞片炉条二件；中夹板一件；边夹板一件；滚柱一件；横梁炉排中片二件；阀体一件；适配器一件；法兰二件。

The direct stress distrilouted on the cross-section of flexed "I" girder has been determined with electrometic method in this paper.

本试验主要通过电测法测定：工字梁在弯曲时横截面上的正应力分布，并与理论值比较，以验证弯曲正应力公式，并且对材料合理选用进行分析。

There is an analysis of spatial stress on variable cross-section wide box girder of three-span continuous PC rigid frame bridge in the paper.

对一座铁路三跨连续PC刚构桥变截面宽幅箱梁进行了空间应力分析。

The total construction process of three-span composite steel box-concrete continuous girder bridge having varied cross-section is analyzed by using spatial finite element method.

应用空间有限元方法，对3跨变截面预应力钢箱-混凝土组合连续梁桥进行了建造全过程分析。

Main contents are shown as follows:(1) After comparing all kinds of applied methods, three-bar stimulation analysis method which is simple is selected to calculate coefficients of shear lag on some cross section of box girder.

将空间有限元法和三杆比拟法两者的计算结果进行对比分析，指出了三杆比拟法的适用范围。

The area ratios of 980/1022, 980/1047,(980+1047)/1022 and 980/(1022+1047) cm^(-1) were decreased as the degree of acetification increased which indicated that acetification induced a decrease of crystallinity of starch. And the crystal structure changed from A-type to V-type. For the cross-linking of POCl3, the area ratios of 980/1022, 980/1047,(980+1047)/1022 and 980/(1022+1047) cm^(-1) were also decreased as the degree of cross-linking but the decrease was little compared to that of acetification. The result indicated that cross-linking of POCl3 had little effect on the starch crystal structure.

随着醋酸酯化取代度的增大，980/1022、980/1047、(980+1047)/1022和980/(1022+1047)的相对峰面积的比值均呈现下降趋势，表明醋酸酯化改性会导致淀粉结晶程度降低，结晶形态从A型转变为V型；随着交联度的增大，980/1022、980/1047、(980+1047)/1022和980/(1022+1047)的相对峰面积比值均呈现下降趋势，但下降程度较小，表明三氯氧磷交联对淀粉结晶结构影响不明显。

Three are three major actions that Mn effects fracture behavior in the alloy at room temperature, as follow: One is that Mn fines grains, antiphase domains and weakens dislocation clog, which retain formation of cleavage crackle. The second is that Mn decreases APB energy and promotes slop and cross slip, in particular, a large number of cross slip make deformed APBs transform from line type into zigzag type and the APBs interact and cross each other, resulting in propagation of cleavage cracks. The last is that Mn raises the relative proportion of cleavage strength to grain-boundary strength and then restrains formation and propagation of cleavage crack.

Mn对合金室温断裂行为的影响主要反映在三个方面，一是Mn的存在细化晶粒和反相畴，使得位错塞积程度减小，从而阻碍解理裂纹源的生成；二是Mn的存在提高解理强度与晶界强度的相对比值，从而抑制了解理裂纹的形成和扩展；三是Mn降低反相畴界能量、促进超位错的滑移、交滑移，特别是断裂前位错大量的交滑移使形变反相畴由直线型变为折线"Z"字型，反相畴界间的相互作用、相互交错阻碍了解理裂纹的扩展。

While it is usually impractical for the marshallate to measure blade weight directly by weighing the sword before the basket hilt, cross, or pommel weight is attached, the linear density of the blade (its weight divided by its length) can be estimated fairly easily by weighing the finished sword, locating the point on the blade at which it balances, and measuring the distance from the point of balance to the tip, from the point of balance to the hilt, and from the point of balance to the point where the additional weight (the basket hilt, cross, or cross plus pommel weight) is attached to the blade.

而这通常是不切实际的为marshallate来衡量的刀身Weight直接由称重剑前一篮子的Hilt ，交叉，或pommel重量是重视，线性密度的刀片可估计相当容易称重成品剑，定位点的叶片在它的结余，以及测量距离平衡点，以尖端性，从平衡点到极限和从平衡点以点的额外重量（篮子的Hilt ，交叉，或跨加pommel重量）是连接到刀片。

Liapunov—Schmidt method is one of the most important method in the bifurcation theory.

Liapunov—Schmidt方法是分叉理论的最重要方法之一。

Be courteous -- even when people are most discourteous to you .

要有礼貌──即使当別人对你最不礼貌的时候。